MIDIbox

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== EASY CV ======

Test Equipment: CV-Destination MB33 MAM:\\
{{:phatline:easy-cv-testequipmentv1.jpg?600|}}


===== Introduction =====
All Parameters are saved as a preset as a song (programchange...)\\
Digital created LFO+ENV with CV-Output.\\
No Displays, No Menues, Minimal buttons, much Scopes, much Led-Ring-Rotarys (LRE-8x2CS)\\ 
one big UI with complete functions for one LFO+ENV Voice + 4xChannelstrip Controlls... \\

LFO+ENV are mixed together softwareside, to use only one CV-Output\\
Each Channel = Filter need 8xCV-Outputs\\
Copy Paste for LFOs and ENVelopes between the Voices\\
Copy Paste for a Song aka Preset aka Bank aka Program(change)\\
Jam Style Pattern load (next Preset Display) + Preset Morph between Current-Preset and Next-Preset\\

The Early Design was a EuroRack-Module:
A Breakoutmodule for each CV-Output, with Depth-rotary, Focusswitch (Pushrotary), 2x Scopes (LFO+ENV) and LFO/ENV-Switch to show on one Display the Mixed Waveform & to switch the Rotary to "ENV" or "LFO" Mode (there is only space for one Encoder - maybe just make PAN Style, instead of 2 individual level -maybe more live feel?, how ever when using an 3Stage switch, i could disable MIX-View, or display it on ENV or LFO...maybe a good choise ;) )
The Depth-rotary has no Ledring, want to display it as a bar or as Value in the scope...

===== FrontPanel =====
==== Brain ====
__THE **LEFT** SIDE of the BRAIN  >  Preset-Management:__
**Save** & **Load** the PROGRAM, can be done by Midi-ProgramChange -or With the LOAD-**PRESET**-Encoder\\
then press **LOAD** -or **Morph** to the next Program slowly with the MORPH-Encoder\\
-Another option is to take a **PUSH-ENCODER** for **LOAD** & **STORE** > and load and store it by pushing it... would free 2 buttons for other functions.\\
MORPH?:  \\
-The Upper 7 Segment LED- Display: is the **LOAD Display** indicate the new Program with ENV+LFO
-The downer7 Segment LED- Dsipaly: is the **STORE Display** it indicates also the current Program with ENV+LFO\\  
--with morph you crossfade between both Presets (be carefull, first Store the current Preset\\
**Paste** & **Copy** do their job @ the whole PROGRAM Memory\\     
**ENV-PASTE** & **ENV-COPY** do their job @ the selected Envelope > (ENV-Voice selection is done by the breakout Modules) ... LFO..same\\

Midi-Channel Note NR or Number of Envelope is a real programmer job (C), with usb-upload from computer
.... this is a individual device, and once set, it has to play > and it just should do LFOs and Envelopes
Fixed routed, no generic, special  > in my case for a filterbank.
{{ :phatline:Easy-CV-BRAIN.png?direct&900 |}} 
__THE **RIGHT** SIDE of the BRAIN  >  LFO + ENV Settings (one Voice):__
ADSR with:\\
**CURVE** Paremter which give exponentially to it (no straight lines While Fall and Rise)\\
**Short:** just shorten the Maximal lenght of a Envelope, haveing more Feeling on Encoders
should change Scope Display also... \\
**LFO:** get synced with Midi, and there is a retrigger by Notes...\\
**Phase:** offsets the start-Phase \\
**Delay:** simple delay (nte-Trig)\\
**Rate:** clear from 8 wholes to 128th or so\\
**Wave:** access to the Waveforms\\
**Duration:** interpret Midisync in trippled, whole notes or whatever...\\ 

**DEPTH:** is the maximal Value of FALL and RISE and SUSTAIN, i know i loose resolution with this...but i have to have a memory filterbank,...doing depth instead with Potentiometers on Filtermodules... would give no memory...

==== BreakOut ====
**this will not be supportet > since i dont want a Euro-Module Setup > i want one big filterbox.**\\
1. Discharged UserInterface for the Brain in "Island mode" (Scopes + Digital-CV-Amount)\\
2. CV-Breakout EuroModule to be located near the CV-Destination (example: a Filter).\\
2 Waveforms (ENV+LFO) are mixed together softwareside\\
that bring 2 advanteges:\\
1.save one CV-Output\\
2. the Amplitude of each Waveform is saved in the patch, so the CV-Amount to a Filter is saved in the Patch\\
That bring 2 disadvanteges:\\
1.LFO or ENV cant get patched to individual destination\\
2.the Resulution gets lower 2 very low, and the code has to be adptet much... or have to be made from scratch
Because I use the device for a Memory-Filterbox (VCF+VCA), i am ok with the pros and cons, so  i call it EASY-CV\\
{{ :phatline:Easy-CV-BREAKOUT.png?direct&130 |}} 
**Envelope Scope:** show the ENV-Waveform \\
or the Mixed-CV-Output-Waveform (when Switch is in LFO Mode)\\ 
and show the Envelope-Amount with a BAR or as numeric Value?\\
**MIXED CV Plug:** CV-Output > Mixed Waveform ENV+LFO\\
**Switch @ ENV:**\\
  -Depth-Encoder change ENV Amount of the CV-MIX\\
  -ENV Scope will show ENV Wave\\
  -LFO Scope will Show CV-Mix\\
**Switch @ LFO:** visa versa ENV\\
Press the Encoders built in **ENCODER-BUTTON**:\\
will switch the BRAIN-A-D-S-R and L-F-O ENCODER to the Page for THIS Module...\\ 
workflow, see what you have with a Scope, over a filter, and edit exact this selected CV on the brain in full detail...

==== VCA-VCF ====
**CVś(AOUT):**\\
1.VCF-CUT\\
2.VCF-RES\\
3.FILTER DRIVE\\

4.VCA-ENV\\
5.VCA-DRIVE\\

6.DRY-WET (Orginal vs Filtered Mixer)\\
7.Send 2 EFX1\\
8.Send 2 EFX2\\
So 1x 8AOUT-Module for each "Channelstrip", makes a total of 4x8AOUT-Modules.\\
The Module of Choise is a 16Bit, since i control with the the same AOUT-Channel ENV+CUT-OFF...\\
so there is no analog potentiometer for Cutoff or resonance... it is all saved in the Preset.\\

the VCA is basicly a simple VCA (MS20Like) or something\\
the VCF are a 303 18dB for the 24db Filter it will be a SSM2044, where bords are available.\\

In order to not use those **overprized MATCHED-PAIR-TRANSISTORS** (over 2€ on the cheapest place) i have to use standart Transistors and make a **VBE-MATCH** on my own, i have already a PCB from here - to measure the transistors with a Multimeter:
https://midisizer.com/other/vbe-matching/

==== Example for a Filterbank ====
EUROMODULE-BASED >>> It is not planed to do it that way (just for you to get some input)
{{ :phatline:Easy-CV-Example.jpg?direct&900 |}} 

A not EUROMODULE-BASED Version of something like this is the FILTERBOX: \\
(this is the Design I prefer @ the moment)
{{:phatline:easy-cv-filterbox.png|}}

Filterbox OneChannel > first idea of Block-shematic:
{{:phatline:filterbank-channelstrip.jpg|}}
===== General Design =====

The Panel is made of transparent but shadet (black transparent) Plexiglass.\\
The Panel is directly mounted into a Flightcase.\\
The 3x LRE8x2 (LEDRING) are mounted with the Encoder Nuts, the rest of the PCBs are mounted with normal thruhole screws.\\

==== FrontPanel ====

==== PCBs ====
**The Analog-IO Board on the Backpanel, holds:**\\
-the ENV-VCAs\\
-the DryWet-VCAs, Filter-Releay-Switch\\
-SEND-EFX-VCAs\\
-the Summing Mixer\\
-the Ducking-Cross-AMP-Follower+Ducking-VCAs\\
-VCF+ENV-VCA-Distortion-Driver-VCAs\\
-the Connectors to connect the Filter, AOUT, Poti-Boards\\

Left-Part of the Brain on Breathboard: \\
OLED-Display \\
Button: ShadowSE/ITT\\
ENCODER: with built in Pushswitch\\
a early state with 7Segment Displays to indicate the Patches\\
{{:phatline:proto-preset.jpg?400|}}


==== 1. UI Parts Listing  ====

=== BRAIN + BREAKOUT ===
  * 6,3 Neutrik Connector\\
  * [[http://at.rs-online.com/web/p/kippschalter/7347145|FLASH-Switch @ Rs-components]]

^ Value     ^  Type                    ^ Qty  ^
|Switch     |SPDT Vertical PCB-Mount ON-OFF-ON   |1     |
FIXME Fill Table

=== Pots / Knobs ===

  * [[http://www.alps.com/prod/info/E/HTML/Potentiometer/RotaryPotentiometers/RK11K11/RK11K11_list.html|Alps RK11K Series]]
  * [[https://www.thonk.co.uk/shop/alpha-9mm-pots/|Alpha Pots @ Thonk]]
  * [[where_to_order_components#knobs|Knobs Suppliers]]
  * FIXME which Values for the Audio-Mixer?


==== 3.Footprint Making in KiCAD ====

  * ALPS Pots
  * Alpha Pots
  * 6,3mm Jack
  * Switch
  * Momentary Switch
  * SSD-Displays
  * OLED DIsplay
  * Rotary Encoder
FIXME have to be done

==== 4. Schematics in KiCAD ====

FIXME have to be done

==== 5.PCB Making In Kicad ====

=== PCB Making Order ===
- BRAIN PCBs:\\
 a.Left-Brain\\
 b.Right-Brain\\
- 3x LRE8x2CS - is a generic PCB which i already have (fairlightiiś)\\
- Backpanel PCB\\
- FILTER PCBs\\
MIDIbox

User Tools

Site Tools

Page Tools
