This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
enc_4_4 [2018/03/06 07:45] latigid_on [BOM v1.0] |
enc_4_4 [2018/03/06 18:55] latigid_on [Schematic] |
||
---|---|---|---|
Line 5: | Line 5: | ||
===== Schematic ===== | ===== Schematic ===== | ||
+ | Refer to the SCS schematic or below for J1/button and encoder pinning and the Core module (J15) for J5/OLEDs. | ||
Line 14: | Line 14: | ||
^ Type ^ Part ^ Value ^ | ^ Type ^ Part ^ Value ^ | ||
- | | Caps | C25 | DNF | | + | |Caps | C25 | DNF | |
| | C26 | DNF | | | | C26 | DNF | | ||
| | C29 | 10uF polarised | | | | C29 | 10uF polarised | | ||
- | | Encoder | EN1 | 12mm | | + | |Encoder | EN1 | 12mm | |
| | EN2 | 12mm | | | | EN2 | 12mm | | ||
- | | Header | J1 | PINHD-2X54WALL | | + | |Header | J1 | PINHD-2X54WALL | |
| | J2 | +5V | | | | J2 | +5V | | ||
| | J5 | PINHD-2X54WALL | | | | J5 | PINHD-2X54WALL | | ||
- | | OLEDs | LCD1 | 0.96_OLED | | + | |OLEDs | LCD1 | 0.96_OLED | |
| | LCD2 | 0.96_OLED | | | | LCD2 | 0.96_OLED | | ||
| | LCD3 | 0.96_OLED | | | | LCD3 | 0.96_OLED | | ||
Line 47: | Line 47: | ||
===== Assembly ===== | ===== Assembly ===== | ||
+ | Decide on the configuration to be used. Any combination of switches, encoders or OLEDs is possible if they fit. | ||
+ | Only one encoder is wired to the J1 header. If you want to use the EN2 position, wire the legs to the empty EN1 solder points. | ||
+ | |||
+ | R9 and C29 form the power-on reset for OLEDs. R7 should not be installed. R3/C25/R4/C26 form a termination shunt for OLED data lines. They shouldn't be required. | ||
+ | |||
+ | The switches accommodate either DT6 or 6mm switches (obviously only one type!). For DT6 switches, ensure the flat side is aligned with the PCB silkscreen. | ||
+ | |||
+ | J2 can supply power if needed. | ||
Line 53: | Line 61: | ||
==== Interconnections ==== | ==== Interconnections ==== | ||
- | * J1 | + | {{::scsoled:j1.png?nolink&200|}} |
+ | J1 is the SCS header, connecting to J10A | ||
- | ===== Dimensions ===== | + | J2 can provide power as indicated; it is also connected on J5. |
- | {{:encs:encs.png?link&400|}} | + | J5 connects to J15 on the Core (or equivalent) |
+ | |||
+ | ===== Dimensions ===== | ||
- | {{ :encs:encs_dxf.zip }} | + | {{:scsoled:scsoled.png?link&600|}} |
+ | {{ :scsoled:doku.zip |}} | ||
===== License ===== | ===== License ===== | ||