euro-midi-io
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
euro-midi-io [2022/02/06 06:46] phatline [Frontpanel] |
euro-midi-io [2022/02/11 15:23] (current) phatline [To Do] |
||
|---|---|---|---|
| Line 10: | Line 10: | ||
| {{:phatline:EURO_Midi_IO_Shematic.jpg?900|}}\\ | {{:phatline:EURO_Midi_IO_Shematic.jpg?900|}}\\ | ||
| + | |||
| + | FIXME - The Connection from J1 to J2 is wrong - its 1:1 but it has to be crossed.\\ | ||
| ====== Hardware Requirements ====== | ====== Hardware Requirements ====== | ||
| * Soldering Iron - with a Dip that can Handle Thruhole-Parts and 1206 SMDs, solder Paste...\\ | * Soldering Iron - with a Dip that can Handle Thruhole-Parts and 1206 SMDs, solder Paste...\\ | ||
| Line 77: | Line 79: | ||
| so feel free to test - and report!\\ | so feel free to test - and report!\\ | ||
| {{:phatline:EURO_Midi_IO_Board.jpg?900|}}\\ | {{:phatline:EURO_Midi_IO_Board.jpg?900|}}\\ | ||
| + | FIXME - dont use this - because of J1-J2 connection is wrong (this matter if you chain 2 Midi-IO-Modules\\ | ||
| ====== Frontpanel====== | ====== Frontpanel====== | ||
| {{:phatline:Euro_Midi_IO_Panel-Dimensions.jpg?900|}}\\ | {{:phatline:Euro_Midi_IO_Panel-Dimensions.jpg?900|}}\\ | ||
| - | **I made a DXF File which you can print, and drill it DIY or \\ | + | **I made a {{:phatline:EuroMidiIO-Panel-for-milling.zip?900|DXF}}File which you can print, and drill it DIY or \\ |
| - | you can send to:** (once the prototypestate is gone)\\ | + | you can send to:**\\ |
| [[https://shop.frontpanels.de/custom-panels|frontpanels.de in germany]] 17,08€ a panel (5x-10%, 10x-20%, 20x-30%, 30x-40%, 100x-50%)\\ | [[https://shop.frontpanels.de/custom-panels|frontpanels.de in germany]] 17,08€ a panel (5x-10%, 10x-20%, 20x-30%, 30x-40%, 100x-50%)\\ | ||
| - | Frontpanels.de work:\\ | + | I tested one with them - and yes they looking good - and they fit!:\\ |
| \\ | \\ | ||
| - | [[https://thebeast.co.uk/2d/|The Beast - UK]]\\ | + | another good guy: [[https://thebeast.co.uk/2d/|The Beast - UK]]\\ |
| - | [[https://www.schaeffer-ag.de/en/|Schaeffer-ag.de]] | + | |
| \\ | \\ | ||
| **Recommend Material**\\ | **Recommend Material**\\ | ||
| 2mm x 128.5 x 17.78 Aluminium, anodised\\ | 2mm x 128.5 x 17.78 Aluminium, anodised\\ | ||
| - | {{:phatline:Frontpanel-EuroMidi.zip?900|}} - NOT TESTET\\ | ||
| \\ | \\ | ||
| **A cheaper way is: order a 1,6mm thick Aluminium PCB as Frontpanel:**\\ | **A cheaper way is: order a 1,6mm thick Aluminium PCB as Frontpanel:**\\ | ||
| Line 102: | Line 104: | ||
| ====== To Do ====== | ====== To Do ====== | ||
| - | Since i already debugged Rev.A - and this is the overworked Rev.B - there should not be much to do, except to test the gerber filers... i am happy with Rev.A (have still PCBs so no check of RevB in near future!)\\ | + | Use a other Midi-OUT-Activity Shematic! - its not working for high speed midi! - while Note-ON off is ok, Midiclock can make trouble (the Charge-Discharge Circuit in this Design is not sufficent for this!)\\ |
| ====== Community users working on it ====== | ====== Community users working on it ====== | ||
euro-midi-io.1644130005.txt.gz · Last modified: 2022/02/06 06:46 by phatline
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
