fadercore_-_vlr-motorfader
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
fadercore_-_vlr-motorfader [2014/07/30 11:36] novski |
fadercore_-_vlr-motorfader [2014/11/10 20:22] novski |
||
|---|---|---|---|
| Line 12: | Line 12: | ||
| It contains 2 different Types of PCBs one is the VLR-MF_NG and the other a slim PCB to mount to your Fader so its detachable for service. | It contains 2 different Types of PCBs one is the VLR-MF_NG and the other a slim PCB to mount to your Fader so its detachable for service. | ||
| - | {{:fadercore_vlr-meterboard_beispiel_1_kanal_bestueckt.png?600|}} | ||
| - | Eagle Files: [[https://github.com/novski/Midibox/tree/master/VLR-8x16LEDmeter]] | ||
| - | {{:fadercore_vlr-ledmatrix_unbestueckt_top.png?200|}} {{:fadercore_vlr-meterboard_bestueckt_sideview.png?200|}}\\ | + | Eagle Files: |
| - | {{:fadercore_vlr-ledmatrix_dimensions.png?300|}} {{:fadercore_vlr-meterboard_dimensions.png?200|}} | + | |
| ==== BOM ==== | ==== BOM ==== | ||
| Line 25: | Line 24: | ||
| And look for Local dealers preferred. [[http://www.midibox.org/dokuwiki/doku.php?id=where_to_order_components]] | And look for Local dealers preferred. [[http://www.midibox.org/dokuwiki/doku.php?id=where_to_order_components]] | ||
| - | To make a small and easy to connect matrix over a hole Frontplatte is no fun. Thats why i made myself a better solution. Based on the common DOUT modules it can be connected to 3 SRs. | ||
| == The Materials: Mouser == | == The Materials: Mouser == | ||
| - | * 16x6pin Headers, 649-75869-131LF | + | * |
| - | * 16x6pin Sockets, 649-71600-006LF | + | * 8x6pin Sockets, 649-71600-006LF |
| - | * 20 Wire Ribbon Cable, 523-135-2801-020FT | + | * |
| - | * about 80 Green LEDs, 604-WP3A8GD | + | * 1 Green LED, 604-WP3A8GD |
| - | * about 80 Yellow LEDs, 604-WP3A8YD | + | * |
| - | * about 80 Red LEDs, 604-WP3A8HD | + | |
| - | Project Order Basket on Mouser: [[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=5ecf7b4949]] | + | Project Order Basket on Mouser: [[http://www.mouser.com]] |
| The PCB is available under: | The PCB is available under: | ||
| - | [[https://www.vlrlab.com/home/18-ledmatrix.html]] | + | [[https://www.vlrlab.com] |
| - | [[https://www.vlrlab.com/home/19-meterboard.html]] | + | [[https://www.vlrlab.com] |
| ==== How to get Started ==== | ==== How to get Started ==== | ||
| - | The LEDs are mounted to the Edge of the Meterboard to get a very slim form. That makes it a bit harder to solder them but i guess that no one wont be able to do it. | + | |
| - | To solder the Header to the Edge there is a wite triangle printed to the PCB on one side. This Triange has to match with the Triangle on the Header. | + | |
| ==== Prepare the PCB ==== | ==== Prepare the PCB ==== | ||
| - | Well you should now by now how to solder Headers... :-) | + | |
| ==== Prepare the Connection ==== | ==== Prepare the Connection ==== | ||
| - | Connect the SEL, Row1-8 & Row9-16 with each a DOUT Header. | + | |
| ==== Test it in MIOS ==== | ==== Test it in MIOS ==== | ||
| \\ | \\ | ||
| - | I use a Encoder connected directly to a DIN to test. | + | |
| - | Assuming that the DOUT is the first device on the chain of J8/9 we need to configure it like this:\\ | + | |
| - | \\ | + | |
| - | RESET_HW\\ | + | |
| - | \\ | + | |
| - | LCD "%C"\\ | + | |
| - | LCD "@(1:1:1)OLED1"\\ | + | |
| - | \\ | + | |
| - | # Test D-OUT LEDmatrix board\\ | + | |
| - | \\ | + | |
| - | DOUT_MATRIX n=1 rows=8 inverted=1 sr_dout_sel1=1 sr_dout_r1=2 sr_dout_r2=3\\ | + | |
| - | \\ | + | |
| - | # Matrix control by a Encoder connected to DIN\\ | + | |
| - | ENC n=1 sr=1 pins=0:1 type=detented2\\ | + | |
| - | \\ | + | |
| - | EVENT_ENC id= 1 fwd_id=LED_MATRIX:1 type=CC chn= 1 cc= 24 lcd_pos=1:1:2 label="^std_enc" LED_MATRIX_PATTERN=1\\ | + | |
| - | \\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos= 0 pattern=0000000000000000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos= 1 pattern=1000000000000000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos= 2 pattern=1100000000000000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos= 3 pattern=1110000000000000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos= 4 pattern=1111000000000000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos= 5 pattern=1111100000000000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos= 6 pattern=1111110000000000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos= 7 pattern=1111111000000000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos= M pattern=1111111100000000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos= 8 pattern=1111111110000000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos= 9 pattern=1111111111000000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos=10 pattern=1111111111100000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos=11 pattern=1111111111110000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos=12 pattern=1111111111111000\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos=13 pattern=1111111111111100\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos=14 pattern=1111111111111110\\ | + | |
| - | LED_MATRIX_PATTERN n= 1 pos=15 pattern=1111111111111111\\ | + | |
| - | \\ | + | |
| - | Im using my VLR-8oDisp board to show the Values of the encoder. You can change it to any other type of Display-setting... lcd_pos=6:1:5 {6=Display number : 1= X-axis : 5= Y-Axis (row)} | + | |
| For any Comment or Question: Forum Thread??? | For any Comment or Question: Forum Thread??? | ||
fadercore_-_vlr-motorfader.txt · Last modified: 2014/11/10 20:22 by novski
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
