User Tools

Site Tools


seqv4plus_le_mec

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
seqv4plus_le_mec [2017/11/20 18:01]
latigid_on [BOM v1.0]
seqv4plus_le_mec [2018/12/18 09:35] (current)
latigid_on [BOM v1.0]
Line 1: Line 1:
-====== SEQv4+ le MEC ======+====== SEQv4+ le mec ======
  
 This board holds the SEQ's illuminated buttons, which are driven from a shift register matrix. The [[seqv4plus_enc-plate|ENC-PLATE]] board stacks on top. This board holds the SEQ's illuminated buttons, which are driven from a shift register matrix. The [[seqv4plus_enc-plate|ENC-PLATE]] board stacks on top.
Line 6: Line 6:
 ===== Schematic ===== ===== Schematic =====
  
-A shift register chain of 3 DIN 74HC165 and 2 DOUT 74HC595 chips are used. Two of the DINs scan the encoders and one scans the button columns. The DOUT parts are connected into a matrix. Note that both the high and low sides have driver transistors (PNP and NPN, respectively). This means that the anode side of the matrix will operate with inverted behaviour (pin high = LED off).+A shift register chain of 3 DIN 74HC165 and 2 DOUT 74HC595 chips are used. Two of the DINs scan the encoders and one scans the button columns. The DOUT parts are connected into a matrix. Note that both the high and low sides have driver transistors (PNP and NPN, respectively). This means that the anode side of the matrix will operate with inverted behaviour (pin high = LED off). Actually the low (cathode) side is also "​inverted,"​ as we turn the transistor "​on"​ to sink the current by toggling the 595 pin high
  
 There are special instructions for connecting the parts which are covered below. There are special instructions for connecting the parts which are covered below.
Line 12: Line 12:
  
 ===== BOM v1.0 ===== ===== BOM v1.0 =====
 +
 +**Please find the current BOM on [[http://​midiphy.com]]. The table below is depreciated and will not be updated.**
 +
  
 ^Type     ​^Qty ^Value  ​  ​^Package ^Parts^Mouser^Reichelt^Conrad^Other^Notes^ ^Type     ​^Qty ^Value  ​  ​^Package ^Parts^Mouser^Reichelt^Conrad^Other^Notes^
Line 19: Line 22:
 |         ​|10 ​  ​|100-220R 5%   |THT or 1206 |SJ1-8, RJ9    |      |        |      |     |see instructions | |         ​|10 ​  ​|100-220R 5%   |THT or 1206 |SJ1-8, RJ9    |      |        |      |     |see instructions |
 |         ​|16 ​  |1k 5%         |THT |R1-16 ​ |      |        |      |     | | |         ​|16 ​  |1k 5%         |THT |R1-16 ​ |      |        |      |     | |
 +|         ​|8 ​   |10k 5%         |1206 |R18-25 ​ |      |        |      |     |near NPN transistors |
 ^Resistor networks^^^^^^^^^^ ^Resistor networks^^^^^^^^^^
 |         ​|3 ​   |9*10k ​  ​|SIP10 |RN1-3 ​ |      |        |      |     ​|bussed network, __not__ 5 pairs of resistors | |         ​|3 ​   |9*10k ​  ​|SIP10 |RN1-3 ​ |      |        |      |     ​|bussed network, __not__ 5 pairs of resistors |
Line 26: Line 30:
 ^Diodes^^^^^^^^^^  ^Diodes^^^^^^^^^^
 |         ​|24 ​   |1N4148 |THT         ​| ​           |      |        |      |     | |  |         ​|24 ​   |1N4148 |THT         ​| ​           |      |        |      |     | | 
-|         ​|24 ​   |BAT54|SOT-23 |            |512-BAT54 ​     |BAT 54 SMD        |      |     |(for prototypes, stack on top of BC818 transistors ​+|         ​|24 ​   |BAT54|SOT-23 |            |512-BAT54 ​     |BAT 54 SMD        |      |     | | 
 ^LEDs^^^^^^^^^^  ^LEDs^^^^^^^^^^
 |         |16 |RGB flat |superflux ​ |            |      |        |      |ELV: 68-10 94 64     |see instructions| ​ |         |16 |RGB flat |superflux ​ |            |      |        |      |ELV: 68-10 94 64     |see instructions| ​
seqv4plus_le_mec.1511200868.txt.gz ยท Last modified: 2017/11/20 18:01 by latigid_on