User Tools

Site Tools


wilba_mb_seq_parts_guide

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
wilba_mb_seq_parts_guide [2008/10/22 02:40]
Wilba
wilba_mb_seq_parts_guide [2018/03/07 21:59] (current)
goyousalukis
Line 1: Line 1:
-**In progress, pictures and specifications not yet added**+**WORK IN PROGRESS** 
 +===== Parts List ===== 
 +\\ 
 +This parts list corresponds to the PCB labeling on the Wilba Control Surface PCB sold by ModularAddict.com
  
-Rotary Encoder:+^Name       ​^Part ​                   ^Value ​ ^Quantity ^Reichelt Order Code ^Mouser^ 
 +|**Regular Parts** ​                                                     |||||| 
 +|C1-C8 ​    ​|Capacitor ​             |100nF ​  ​|8 ​       |Z5U-2,5 100N        |594-A104K15X7RF5UAA ​ | 
 +|D1-58 ​    | Diode| 1N4148 |58 |1N 4148        |512-1N4148 ​           | 
 +|E1-17|Encoder+| |17 | |652-PEC16-4220FN0024| 
 +|L1-16|Bicolor LEDs (red/green, 3mm round, diffused, common cathode)| |16| |859-LTL1BEKVJNN| 
 +|L17-20, L31-34, L40-58 |LED green, 3mm round, diffused| |27| |859-LTL-4231| 
 +| |Tempo LED|5mm|1| |604-WP483IDT| 
 +|R1-R8A|1/​4W Resistor |220 ohms (match to your LEDs)|10| |660-MF1/​4DC2200F| 
 +|RN1-12|6 Pin SIL resistor network|10k|12||264-10K-RC| 
 +|SW1-58|Tactile Switches 12X7.3MM 160GF| |58| |TL1100F160Q| 
 +| |Switch Caps Switch Cap Rectangle Black| |58| |611-PEBK| 
 +|U1-U6|74HC165 shift register| |6| |595-SN74HC165N| 
 +|U7-8|74HC595 shift register| |2| |595-SN74HC595N| 
 +| | |16 pin IC Socket| | |575-199316| 
 +|J1-2|10 pin IDC Socket++|10 pin|2| |571-5103309-1| 
 +| |10 Pin IDC Header|10 pin|2| |710-61201023021| 
 + 
 ++ see details about different encoder options below 
 + 
 +++ consider alternate sources like Amazon, AliExpress, eBay, ect.. for IDC headers/​sockets. They are often sold in bags of 10. 
 + 
 +**REQUIRED AND WILL INCLUDE IN BULK ORDER** 
 + 
 +17x Rotary Encoder:
 A "​standard"​ 16mm, 24 detent, 24 pulse encoder, however the shaft length and bushing must match. They are the same ones as used on the MB-6582. A "​standard"​ 16mm, 24 detent, 24 pulse encoder, however the shaft length and bushing must match. They are the same ones as used on the MB-6582.
  
 If you already have encoders from Voti: [[http://​www.voti.nl/​winkel/​catalog.html?​SW-ROT]] or from a bulk order for Soundwell, then these will work.  If you already have encoders from Voti: [[http://​www.voti.nl/​winkel/​catalog.html?​SW-ROT]] or from a bulk order for Soundwell, then these will work. 
  
-Datawheel Knob:+16x black Re'an P401 soft-touch knobs. 
 + 
 +Identical to those distributed in nebula'​s bulk order: [[http://​www.midibox.org/​forum/​index.php/​topic,​11050.0.html]] 
 + 
 +1x Datawheel Knob:
  
 ALBS P/N 866003, Drehknopf DK38-144 A.6/4,5 schwarz gerillt mit Fingermuld, datasheet: [[http://​www.albs.de/​ecom/​images/​866003.pdf]] ALBS P/N 866003, Drehknopf DK38-144 A.6/4,5 schwarz gerillt mit Fingermuld, datasheet: [[http://​www.albs.de/​ecom/​images/​866003.pdf]]
Line 12: Line 43:
 Note also the rotary encoder for the datawheel is "panel mounted"​ to the PCB, so you can adjust it's height down by maybe 5mm max. and also optionally mount it above the PCB. Also, you can adjust how much you push the knob onto the rotary encoder shaft, or shorten the shaft (it's a plastic shaft) to suit other kinds of datawheel knobs. Note also the rotary encoder for the datawheel is "panel mounted"​ to the PCB, so you can adjust it's height down by maybe 5mm max. and also optionally mount it above the PCB. Also, you can adjust how much you push the knob onto the rotary encoder shaft, or shorten the shaft (it's a plastic shaft) to suit other kinds of datawheel knobs.
  
-Switch:+58x Switch:
 [[http://​www.digikey.com/​scripts/​DkSearch/​dksus.dll?​Detail?​name=EG1821-ND]] [[http://​www.digikey.com/​scripts/​DkSearch/​dksus.dll?​Detail?​name=EG1821-ND]]
 [[http://​www.mouser.com/​search/​ProductDetail.aspx?​qs=7Bi7Dg8SEnw0f0sbwKIXZA%3d%3d]] [[http://​www.mouser.com/​search/​ProductDetail.aspx?​qs=7Bi7Dg8SEnw0f0sbwKIXZA%3d%3d]]
Line 18: Line 49:
 * switch is a "​standard"​ 12x12mm tactile switch, but the rectangular switch cap specified below requires this exact switch. * switch is a "​standard"​ 12x12mm tactile switch, but the rectangular switch cap specified below requires this exact switch.
  
-Switch cap (black): +Added Aug 2015:
-[[http://​www.digikey.com/​scripts/​DkSearch/​dksus.dll?​Detail?​name=401-1152-ND]] +
-[[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=qUgWstB0J2Od%252btwj9sasJw%3d%3d]]+
  
-* switch cap requires the switch specified above.+The current PCB from SmashTV has footprints for alternate tact switches
  
 +Namely: TL-1240 [[http://​www.mouser.com/​ds/​2/​140/​TL1240-346152.pdf]] and Mec 3F series [[http://​www.mouser.com/​ProductDetail/​MEC-Switches/​3FTH9/?​qs=sGAEpiMZZMsqIr59i2oRcvYAxqB10yDKjM3xh7wCZYw%3d]]
  
 +The TL-1240 are short (8.2mm) so they cannot be used with encoders installed but are wired correctly for the LEDs.
 +The Mec parts are tall and have a variety of caps but the LEDs are NOT wired to anything despite having pads and will need to be wired by hand.  The 3 pin LEDs cannot be used with these switches. ​ Only the 3F Mec parts are suitable, the 5F and others may fit the footprint, but use a different scheme for the LEDs that wont work at all with this board
  
-MIDI socket+58x Switch cap (black)
-[[http://search.digikey.com/​scripts/​DkSearch/​dksus.dll?​Detail?​name=CP-1235-ND]]+[[http://www.digikey.com/​scripts/​DkSearch/​dksus.dll?​Detail?​name=401-1152-ND]] 
 +[[http://​www.mouser.com/​ProductDetail/​CK-Components/​PE-BK/?​qs=sGAEpiMZZMsqIr59i2oRctAaD8wfjvPOMa0ZOJ%252b2auk%3d]]
  
-Power switch+switch ​cap requires the switch specified above.
-[[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=ewGlpqF2icnsBB85JMTsOw%3d%3d]] +
- +
-Power socket: +
-[[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=4bc6C%252bcluO4fnW%2f1OprFbw%3d%3d]]+
  
- +16x Bicolor LEDs (red/green, 3mm round, diffused, common cathode): Mouser 859-LTL1BEKVJNN
- +
-Bicolor LEDs (red/green, 3mm, diffused, common cathode): Mouser 859-LTL1BEKVJNN+
 [[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=RgVUBjWRgaCkUwHnXSBfYg%3d%3d]] [[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=RgVUBjWRgaCkUwHnXSBfYg%3d%3d]]
  
-10k 6 Pin SIL resistor network:+8x Ceramic Cap 100nF=.1uF "​104"​ (small axial to fit inside DIP-16 IC socket): Mouser 80-C412C104K5R 
 +[[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=TOu4hTA4Gk%2fBW6gm%252bN6zDg%3d%3d]] 
 + 
 +12x 10k 6 Pin SIL resistor network:
 Mouser 264-10K-RC Mouser 264-10K-RC
 [[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=%252bVbJVVxFI2tJO43guEitAw%3d%3d]] [[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=%252bVbJVVxFI2tJO43guEitAw%3d%3d]]
  
-Ceramic Cap 100nF=.1uF "​104"​ (small axial to fit inside DIP-16 IC socket): Mouser 80-C412C104K5R 
-[[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=TOu4hTA4Gk%2fBW6gm%252bN6zDg%3d%3d]] 
  
-74HC165: Mouser 511-M74HC165+ 
 +**REQUIRED AND MAY NOT INCLUDE IN BULK ORDER** 
 + 
 +1x LED (red, 5mm round, diffused) 
 + 
 +27x (28x?) LEDs (green, 3mm round, diffused) 
 + 
 +6x 74HC165: Mouser 511-M74HC165
 [[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=Mu9A%252bxKg3hTmyJWEPt0thA%3d%3d]] [[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=Mu9A%252bxKg3hTmyJWEPt0thA%3d%3d]]
  
-74HC595: Mouser 511-M74HC595+2x 74HC595: Mouser 511-M74HC595
 [[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=lgHKUCmDFtiUPdphCdakWQ%3d%3d]] [[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=lgHKUCmDFtiUPdphCdakWQ%3d%3d]]
  
-16-pin DIP IC socket: Mouser 571-1-390261-4+8x 16-pin DIP IC socket: Mouser 571-1-390261-4
 [[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=VZ9FDhhp7Sk4VC7kJdoJYg%3d%3d]] [[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=VZ9FDhhp7Sk4VC7kJdoJYg%3d%3d]]
  
-1N4148 (small signal diode): Mouser 512-1N4148+58x 1N4148 (small signal diode): Mouser 512-1N4148
 [[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=i4Fj9T%2foRm8RMUhj5DeFQg%3d%3d]] [[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=i4Fj9T%2foRm8RMUhj5DeFQg%3d%3d]]
 +
 +2x 2x5 dual row headers (for DIN/OUT connection to Core/​ultracore and extension to optional button/LED matrix).
 +
 +2x 2x8 dual row headers (for LCDs)
 +
 +IDC connectors to connect LCD and CS boards to Core/​ultracore
 +
 +ribbon cable
 +
 +**REQUIRED AND WILL NOT INCLUDE IN BULK ORDER**
 +
 +2x 2 line 40 character (2x40/40x2) standard character LCD modules
 +
 +**MAY BE USED IN DOUG'S CASE, BUT STILL UNDECIDED**
 +
 +MIDI socket:
 +[[http://​search.digikey.com/​scripts/​DkSearch/​dksus.dll?​Detail?​name=CP-1235-ND]]
 +
 +Power switch:
 +[[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=ewGlpqF2icnsBB85JMTsOw%3d%3d]]
 +
 +Power socket:
 +[[http://​www.mouser.com/​Search/​ProductDetail.aspx?​qs=4bc6C%252bcluO4fnW%2f1OprFbw%3d%3d]]
 +
  
wilba_mb_seq_parts_guide.1224643219.txt.gz · Last modified: 2008/10/22 02:40 by Wilba