This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
wilba_mb_seq_parts_guide [2009/02/04 16:30] Wilba |
wilba_mb_seq_parts_guide [2018/03/07 21:59] (current) goyousalukis |
||
---|---|---|---|
Line 1: | Line 1: | ||
**WORK IN PROGRESS** | **WORK IN PROGRESS** | ||
+ | ===== Parts List ===== | ||
+ | \\ | ||
+ | This parts list corresponds to the PCB labeling on the Wilba Control Surface PCB sold by ModularAddict.com | ||
+ | ^Name ^Part ^Value ^Quantity ^Reichelt Order Code ^Mouser^ | ||
+ | |**Regular Parts** |||||| | ||
+ | |C1-C8 |Capacitor |100nF |8 |Z5U-2,5 100N |594-A104K15X7RF5UAA | | ||
+ | |D1-58 | Diode| 1N4148 |58 |1N 4148 |512-1N4148 | | ||
+ | |E1-17|Encoder+| |17 | |652-PEC16-4220FN0024| | ||
+ | |L1-16|Bicolor LEDs (red/green, 3mm round, diffused, common cathode)| |16| |859-LTL1BEKVJNN| | ||
+ | |L17-20, L31-34, L40-58 |LED green, 3mm round, diffused| |27| |859-LTL-4231| | ||
+ | | |Tempo LED|5mm|1| |604-WP483IDT| | ||
+ | |R1-R8A|1/4W Resistor |220 ohms (match to your LEDs)|10| |660-MF1/4DC2200F| | ||
+ | |RN1-12|6 Pin SIL resistor network|10k|12||264-10K-RC| | ||
+ | |SW1-58|Tactile Switches 12X7.3MM 160GF| |58| |TL1100F160Q| | ||
+ | | |Switch Caps Switch Cap Rectangle Black| |58| |611-PEBK| | ||
+ | |U1-U6|74HC165 shift register| |6| |595-SN74HC165N| | ||
+ | |U7-8|74HC595 shift register| |2| |595-SN74HC595N| | ||
+ | | | |16 pin IC Socket| | |575-199316| | ||
+ | |J1-2|10 pin IDC Socket++|10 pin|2| |571-5103309-1| | ||
+ | | |10 Pin IDC Header|10 pin|2| |710-61201023021| | ||
+ | + see details about different encoder options below | ||
+ | |||
+ | ++ consider alternate sources like Amazon, AliExpress, eBay, ect.. for IDC headers/sockets. They are often sold in bags of 10. | ||
**REQUIRED AND WILL INCLUDE IN BULK ORDER** | **REQUIRED AND WILL INCLUDE IN BULK ORDER** | ||
Line 9: | Line 32: | ||
If you already have encoders from Voti: [[http://www.voti.nl/winkel/catalog.html?SW-ROT]] or from a bulk order for Soundwell, then these will work. | If you already have encoders from Voti: [[http://www.voti.nl/winkel/catalog.html?SW-ROT]] or from a bulk order for Soundwell, then these will work. | ||
+ | |||
+ | 16x black Re'an P401 soft-touch knobs. | ||
+ | |||
+ | Identical to those distributed in nebula's bulk order: [[http://www.midibox.org/forum/index.php/topic,11050.0.html]] | ||
1x Datawheel Knob: | 1x Datawheel Knob: | ||
Line 21: | Line 48: | ||
* switch is a "standard" 12x12mm tactile switch, but the rectangular switch cap specified below requires this exact switch. | * switch is a "standard" 12x12mm tactile switch, but the rectangular switch cap specified below requires this exact switch. | ||
+ | |||
+ | Added Aug 2015: | ||
+ | |||
+ | The current PCB from SmashTV has footprints for alternate tact switches. | ||
+ | |||
+ | Namely: TL-1240 [[http://www.mouser.com/ds/2/140/TL1240-346152.pdf]] and Mec 3F series [[http://www.mouser.com/ProductDetail/MEC-Switches/3FTH9/?qs=sGAEpiMZZMsqIr59i2oRcvYAxqB10yDKjM3xh7wCZYw%3d]] | ||
+ | |||
+ | The TL-1240 are short (8.2mm) so they cannot be used with encoders installed but are wired correctly for the LEDs. | ||
+ | The Mec parts are tall and have a variety of caps but the LEDs are NOT wired to anything despite having pads and will need to be wired by hand. The 3 pin LEDs cannot be used with these switches. Only the 3F Mec parts are suitable, the 5F and others may fit the footprint, but use a different scheme for the LEDs that wont work at all with this board | ||
58x Switch cap (black): | 58x Switch cap (black): | ||
[[http://www.digikey.com/scripts/DkSearch/dksus.dll?Detail?name=401-1152-ND]] | [[http://www.digikey.com/scripts/DkSearch/dksus.dll?Detail?name=401-1152-ND]] | ||
- | [[http://www.mouser.com/Search/ProductDetail.aspx?qs=qUgWstB0J2Od%252btwj9sasJw%3d%3d]] | + | [[http://www.mouser.com/ProductDetail/CK-Components/PE-BK/?qs=sGAEpiMZZMsqIr59i2oRctAaD8wfjvPOMa0ZOJ%252b2auk%3d]] |
* switch cap requires the switch specified above. | * switch cap requires the switch specified above. | ||
Line 58: | Line 94: | ||
[[http://www.mouser.com/Search/ProductDetail.aspx?qs=i4Fj9T%2foRm8RMUhj5DeFQg%3d%3d]] | [[http://www.mouser.com/Search/ProductDetail.aspx?qs=i4Fj9T%2foRm8RMUhj5DeFQg%3d%3d]] | ||
+ | 2x 2x5 dual row headers (for DIN/OUT connection to Core/ultracore and extension to optional button/LED matrix). | ||
+ | |||
+ | 2x 2x8 dual row headers (for LCDs) | ||
+ | |||
+ | IDC connectors to connect LCD and CS boards to Core/ultracore | ||
+ | |||
+ | ribbon cable | ||
**REQUIRED AND WILL NOT INCLUDE IN BULK ORDER** | **REQUIRED AND WILL NOT INCLUDE IN BULK ORDER** | ||
2x 2 line 40 character (2x40/40x2) standard character LCD modules | 2x 2 line 40 character (2x40/40x2) standard character LCD modules | ||
- | |||
**MAY BE USED IN DOUG'S CASE, BUT STILL UNDECIDED** | **MAY BE USED IN DOUG'S CASE, BUT STILL UNDECIDED** |