wilba_mb_seq_parts_guide
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
wilba_mb_seq_parts_guide [2015/08/31 15:08] altitude added info on alternate tact switches |
wilba_mb_seq_parts_guide [2018/03/07 21:59] (current) goyousalukis |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| **WORK IN PROGRESS** | **WORK IN PROGRESS** | ||
| + | ===== Parts List ===== | ||
| + | \\ | ||
| + | This parts list corresponds to the PCB labeling on the Wilba Control Surface PCB sold by ModularAddict.com | ||
| + | ^Name ^Part ^Value ^Quantity ^Reichelt Order Code ^Mouser^ | ||
| + | |**Regular Parts** |||||| | ||
| + | |C1-C8 |Capacitor |100nF |8 |Z5U-2,5 100N |594-A104K15X7RF5UAA | | ||
| + | |D1-58 | Diode| 1N4148 |58 |1N 4148 |512-1N4148 | | ||
| + | |E1-17|Encoder+| |17 | |652-PEC16-4220FN0024| | ||
| + | |L1-16|Bicolor LEDs (red/green, 3mm round, diffused, common cathode)| |16| |859-LTL1BEKVJNN| | ||
| + | |L17-20, L31-34, L40-58 |LED green, 3mm round, diffused| |27| |859-LTL-4231| | ||
| + | | |Tempo LED|5mm|1| |604-WP483IDT| | ||
| + | |R1-R8A|1/4W Resistor |220 ohms (match to your LEDs)|10| |660-MF1/4DC2200F| | ||
| + | |RN1-12|6 Pin SIL resistor network|10k|12||264-10K-RC| | ||
| + | |SW1-58|Tactile Switches 12X7.3MM 160GF| |58| |TL1100F160Q| | ||
| + | | |Switch Caps Switch Cap Rectangle Black| |58| |611-PEBK| | ||
| + | |U1-U6|74HC165 shift register| |6| |595-SN74HC165N| | ||
| + | |U7-8|74HC595 shift register| |2| |595-SN74HC595N| | ||
| + | | | |16 pin IC Socket| | |575-199316| | ||
| + | |J1-2|10 pin IDC Socket++|10 pin|2| |571-5103309-1| | ||
| + | | |10 Pin IDC Header|10 pin|2| |710-61201023021| | ||
| + | + see details about different encoder options below | ||
| + | |||
| + | ++ consider alternate sources like Amazon, AliExpress, eBay, ect.. for IDC headers/sockets. They are often sold in bags of 10. | ||
| **REQUIRED AND WILL INCLUDE IN BULK ORDER** | **REQUIRED AND WILL INCLUDE IN BULK ORDER** | ||
| Line 32: | Line 55: | ||
| Namely: TL-1240 [[http://www.mouser.com/ds/2/140/TL1240-346152.pdf]] and Mec 3F series [[http://www.mouser.com/ProductDetail/MEC-Switches/3FTH9/?qs=sGAEpiMZZMsqIr59i2oRcvYAxqB10yDKjM3xh7wCZYw%3d]] | Namely: TL-1240 [[http://www.mouser.com/ds/2/140/TL1240-346152.pdf]] and Mec 3F series [[http://www.mouser.com/ProductDetail/MEC-Switches/3FTH9/?qs=sGAEpiMZZMsqIr59i2oRcvYAxqB10yDKjM3xh7wCZYw%3d]] | ||
| - | The TL-1240 are short (8.2mm) so they cannot be used with encoders installed but are wired correctly for the LEDs | + | The TL-1240 are short (8.2mm) so they cannot be used with encoders installed but are wired correctly for the LEDs. |
| The Mec parts are tall and have a variety of caps but the LEDs are NOT wired to anything despite having pads and will need to be wired by hand. The 3 pin LEDs cannot be used with these switches. Only the 3F Mec parts are suitable, the 5F and others may fit the footprint, but use a different scheme for the LEDs that wont work at all with this board | The Mec parts are tall and have a variety of caps but the LEDs are NOT wired to anything despite having pads and will need to be wired by hand. The 3 pin LEDs cannot be used with these switches. Only the 3F Mec parts are suitable, the 5F and others may fit the footprint, but use a different scheme for the LEDs that wont work at all with this board | ||
wilba_mb_seq_parts_guide.1441033703.txt.gz ยท Last modified: 2015/08/31 15:08 by altitude
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
