loopa-eurorack-panel
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision Next revision Both sides next revision | ||
|
loopa-eurorack-panel [2022/01/16 04:36] phatline created |
loopa-eurorack-panel [2022/01/21 12:49] phatline [Frontpanel] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | test | + | ====== LoopA - Eurorack - Frontpanel with breakout PCB ====== |
| + | {{:phatline:Euro-LoopA-Breakout-3D.jpg?600|}}\\ | ||
| + | {{:phatline:Euro-LoopA-Frontpanel.jpg?900|}}\\ | ||
| + | |||
| + | **I made this Breakout-PCB and Frontpanel for the midiphy LoopA [[https://www.midiphy.com/en/loopa-v2/|midiphy LoopA]]**\\ | ||
| + | |||
| + | **PCB Size is 172x24mm**\\ | ||
| + | You have to decide if you want Midi Out 3 or the Gate OUT (space thing)\\ | ||
| + | The Reset Switch and the SD, Card, are still on the base PCB...\\ | ||
| + | If you want use the PCB you dont have place for the stock DIN Sockets!\\ | ||
| + | |||
| + | {{:phatline:Euro-LoopA-Breakout-Top.jpg?900|}}\\ | ||
| + | {{:phatline:Euro-LoopA-Breakout-Back.jpg?900|}}\\ | ||
| + | |||
| + | ON this board we have 3 micromatch Connectors, which are crimped fast on a cable\\ | ||
| + | On the other side of the cable you have to solder directly to the Base-PCB,\\ | ||
| + | be carefull while soldering - and follow the shematic, which is layout for 3.5 Jack Midi Type B!\\ | ||
| + | {{:phatline:Euro-LoopA-Breakout-Shematic.jpg?900|}}\\ | ||
| + | {{:phatline:Euro-LoopA-Breakout-Shematic.pdf?900|Schematic}}\\ | ||
| + | |||
| + | |||
| + | ====== Hardware Requirements ====== | ||
| + | *[[https://www.midiphy.com/en/shop-details/120/69/loopa-enhanced-caseless-essential-kit-diy-requantizing-performance-midi-sequencer-midiphy-midibox-stm32f4|midiphy LoopA caseless Kit]] | ||
| + | * Soldering Iron - with a Dip that can Handle Thruhole-Parts, solder Paste...\\ | ||
| + | * The other Parts from the BOM\\ | ||
| + | |||
| + | ====== Building and BOM====== | ||
| + | All necessery Information is printet on the PCB, but also check the Shematic...\\ | ||
| + | |||
| + | 5x [[https://www.buerklin.com/de/Montageblock/p/17H917|Leiterplatten Montageblock aka Standoffs]]\\ | ||
| + | 3x [[https://www.mouser.at/ProductDetail/TE-Connectivity/1-215079-0?qs=sGAEpiMZZMu2UVWuvJ5cF0NzRP25WJYp|Micromatch Socket 2x5Pole 1,27mm]]\\ | ||
| + | 6x [[https://www.mouser.at/ProductDetail/TE-Connectivity/1-2178712-0?qs=Xjc0wECptJBhQ3iBLfHBBw%3D%3D|Micromatch Crimp Connector]] you need only 3, the 3+ is for fails by crimping\\ | ||
| + | 1x [[https://www.mouser.at/ProductDetail/3M-Electronic-Solutions-Division/3365-10-CUT-LENGTH?qs=IOh0O5QtZ92VWnFEwLTckA%3D%3D|Flat Cable 1,27mm pitch]]\\ | ||
| + | 1x [[https://www.mouser.at/ProductDetail/Molex/67068-7041?qs=%2Fha2pyFadugeFcqiSbHe2F3FlkyTY7p9rg69fYk%252bS0tr8kIPu4fJmw%3D%3D|USB-Socket]]\\ | ||
| + | 8x [[https://www.mouser.at/ProductDetail/CUI-Devices/SJ1-3535NG?qs=sGAEpiMZZMv0W4pxf2HiVz9SCMkER55fXrlpiF5mEoVt2p3Qc8GC6g%3D%3D|3,5 Audio Jack]]\\ | ||
| + | 12x [[https://www.mouser.at/ProductDetail/Lumex/SSL-LX30FT4ID?qs=sGAEpiMZZMuCm2JlHBGefjo7mRik%2FjcaqjK5FJOZhDc%3D|Round 3mm Thruhole LEDs-RED-Flat]]\\ | ||
| + | 4x [[https://www.mouser.at/ProductDetail/Lumex/SSL-LX30FT4GD?qs=sGAEpiMZZMuCm2JlHBGefjo7mRik%2FjcaResH8h9wozw%3D|Round 3mm Thruhole LEDs-GREEN-Flat]] | ||
| + | \\ | ||
| + | And there will be some additional Fasting Material, like bolts, Screws, Standoffs, that i dont know right now, because the first protoype has to be built first...\\ | ||
| + | |||
| + | ====== Frontpanel====== | ||
| + | {{:phatline:Euro-LoopA-Frontpanel-growing.jpg?900|}}\\ | ||
| + | **I made a DXF File which you can send to:** (once the prototypestate is gone)\\ | ||
| + | [[https://www.formulor.de|Formulor in Germany]] - Acrylic ... 2Pieces incl shipping 42€\\ | ||
| + | [[https://shop.frontpanels.de/custom-panels|frontpanels.de in germany]] my choose\\ | ||
| + | [[https://thebeast.co.uk/2d/|The Beast - UK]]\\ | ||
| + | [[https://www.schaeffer-ag.de/en/|Schaeffer-ag.de]] | ||
| + | \\ | ||
| + | **Recommend Material**\\ | ||
| + | 2mm x 128.5 x 188.58 Aluminium, anodised\\ | ||
| + | contact frontpanels: info@frontpanels.de\\ | ||
| + | {{:phatline:Frontpanels-Euroloopa.zip?900|}} - NOT TESTET - REVERSE ENGENEERING!!!!!!\\ | ||
| + | |||
| + | |||
| + | ====== To Do ====== | ||
| + | waiting for the PCBs and Panels... since the Panels are reverse - engineered - its praying for good luck!\\ | ||
| + | |||
| + | ====== Community users working on it ====== | ||
| + | * **[[Phatline]]** = PCB & Shematic, Documentation...\\ | ||
| + | |||
| + | Just let a Private message on the forum to user already involved.\\ | ||
loopa-eurorack-panel.txt · Last modified: 2022/02/24 21:27 by phatline
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
