loopa-eurorack-panel
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revisionLast revisionBoth sides next revision | ||
| loopa-eurorack-panel [2022/01/16 04:36] – created phatline | loopa-eurorack-panel [2022/02/10 12:43] – phatline | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | test | + | ====== LoopA - Eurorack - Frontpanel with breakout PCB ====== |
| + | {{: | ||
| + | {{: | ||
| + | |||
| + | **I made this Breakout-PCB and Frontpanel for the midiphy LoopA [[https:// | ||
| + | |||
| + | **PCB Size is 172x24mm**\\ | ||
| + | You have to decide if you want Midi Out 3 or the Gate OUT (space thing)\\ | ||
| + | The Reset Switch and the SD, Card, are still on the base PCB...\\ | ||
| + | If you want use the PCB you dont have place for the stock DIN Sockets!\\ | ||
| + | |||
| + | {{: | ||
| + | {{: | ||
| + | |||
| + | ON this board we have 3 micromatch Connectors, which are crimped fast on a cable\\ | ||
| + | On the other side of the cable you have to solder directly to the Base-PCB, | ||
| + | be carefull while soldering - and follow the shematic, which is layout for 3.5 Jack Midi Type B!\\ | ||
| + | {{: | ||
| + | {{: | ||
| + | |||
| + | |||
| + | ====== Hardware Requirements ====== | ||
| + | *[[https:// | ||
| + | * Soldering Iron - with a Dip that can Handle Thruhole-Parts, | ||
| + | * The other Parts from the BOM\\ | ||
| + | |||
| + | ====== Building and BOM====== | ||
| + | All necessery Information is printet on the PCB, but also check the Shematic...\\ | ||
| + | |||
| + | 5x [[https:// | ||
| + | 3x [[https:// | ||
| + | 6x [[https:// | ||
| + | 1x [[https:// | ||
| + | 1x [[https:// | ||
| + | 8x [[https:// | ||
| + | 12x [[https:// | ||
| + | 4x [[https:// | ||
| + | \\ | ||
| + | And there will be some additional Fasting Material, like bolts, Screws, Standoffs, that i dont know right now, because the first protoype has to be built first...\\ | ||
| + | |||
| + | ====== Frontpanel====== | ||
| + | {{: | ||
| + | **I made a DXF File which you can send to:** (once the prototypestate is gone)\\ | ||
| + | [[https:// | ||
| + | [[https:// | ||
| + | [[https:// | ||
| + | [[https:// | ||
| + | \\ | ||
| + | **Recommend Material**\\ | ||
| + | 2mm x 128.5 x 188.58 Aluminium, anodised\\ | ||
| + | contact frontpanels: | ||
| + | {{: | ||
| + | |||
| + | ====== Interconnection to LoopA ====== | ||
| + | To most connections are Midi... so before start, take a look at some standards: | ||
| + | {{: | ||
| + | |||
| + | ====== To Do ====== | ||
| + | waiting for the PCBs and Panels... since the Panels are reverse - engineered - its praying for good luck!\\ | ||
| + | |||
| + | ====== Community users working on it ====== | ||
| + | * **[[Phatline]]** = PCB & Shematic, Documentation...\\ | ||
| + | |||
| + | Just let a Private message on the forum to user already involved.\\ | ||
loopa-eurorack-panel.txt · Last modified: 2022/02/24 21:27 by phatline