This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
loopa-eurorack-panel [2022/01/16 07:51] phatline |
loopa-eurorack-panel [2022/02/10 12:43] phatline |
||
---|---|---|---|
Line 10: | Line 10: | ||
If you want use the PCB you dont have place for the stock DIN Sockets!\\ | If you want use the PCB you dont have place for the stock DIN Sockets!\\ | ||
- | {{:phatline:Euro-LoopA-Breakout-Top.jpg?500|}}\\ | + | {{:phatline:Euro-LoopA-Breakout-Top.jpg?900|}}\\ |
- | {{:phatline:Euro-LoopA-Breakout-Back.jpg?500|}}\\ | + | {{:phatline:Euro-LoopA-Breakout-Back.jpg?900|}}\\ |
ON this board we have 3 micromatch Connectors, which are crimped fast on a cable\\ | ON this board we have 3 micromatch Connectors, which are crimped fast on a cable\\ | ||
On the other side of the cable you have to solder directly to the Base-PCB,\\ | On the other side of the cable you have to solder directly to the Base-PCB,\\ | ||
- | be carefull while soldering - and follow the shematic, which is 3.5 Jack Midi Type B!\\ | + | be carefull while soldering - and follow the shematic, which is layout for 3.5 Jack Midi Type B!\\ |
- | {{:phatline:Euro-LoopA-Breakout-Shematic.jpg?500|}}\\ | + | {{:phatline:Euro-LoopA-Breakout-Shematic.jpg?900|}}\\ |
- | {{:phatline:Euro-LoopA-Breakout-Shematic.pdf?500|Schematic}}\\ | + | {{:phatline:Euro-LoopA-Breakout-Shematic.pdf?900|Schematic}}\\ |
Line 26: | Line 26: | ||
====== Building and BOM====== | ====== Building and BOM====== | ||
- | All necessery is printet on the PCB, but also check the Shematic...\\ | + | All necessery Information is printet on the PCB, but also check the Shematic...\\ |
- | 8x 1Row 7Pin headers (2.54mm pitch)\\ | + | 5x [[https://www.buerklin.com/de/Montageblock/p/17H917|Leiterplatten Montageblock aka Standoffs]]\\ |
- | 8x 1K 1208 SMD Resistors\\ | + | 3x [[https://www.mouser.at/ProductDetail/TE-Connectivity/1-215079-0?qs=sGAEpiMZZMu2UVWuvJ5cF0NzRP25WJYp|Micromatch Socket 2x5Pole 1,27mm]]\\ |
- | 12x 10uF 1208 Capacitors (non polarized)\\ | + | 6x [[https://www.mouser.at/ProductDetail/TE-Connectivity/1-2178712-0?qs=Xjc0wECptJBhQ3iBLfHBBw%3D%3D|Micromatch Crimp Connector]] you need only 3, the 3+ is for fails by crimping\\ |
- | 3x 10K 0603 SMD Resistors which are optional\\ | + | 1x [[https://www.mouser.at/ProductDetail/3M-Electronic-Solutions-Division/3365-10-CUT-LENGTH?qs=IOh0O5QtZ92VWnFEwLTckA%3D%3D|Flat Cable 1,27mm pitch]]\\ |
- | {{:phatline:LRE-OLED-BAR-3D-Back.jpg?700|}}\\ | + | 1x [[https://www.mouser.at/ProductDetail/Molex/67068-7041?qs=%2Fha2pyFadugeFcqiSbHe2F3FlkyTY7p9rg69fYk%252bS0tr8kIPu4fJmw%3D%3D|USB-Socket]]\\ |
+ | 8x [[https://www.mouser.at/ProductDetail/CUI-Devices/SJ1-3535NG?qs=sGAEpiMZZMv0W4pxf2HiVz9SCMkER55fXrlpiF5mEoVt2p3Qc8GC6g%3D%3D|3,5 Audio Jack]]\\ | ||
+ | 12x [[https://www.mouser.at/ProductDetail/Lumex/SSL-LX30FT4ID?qs=sGAEpiMZZMuCm2JlHBGefjo7mRik%2FjcaqjK5FJOZhDc%3D|Round 3mm Thruhole LEDs-RED-Flat]]\\ | ||
+ | 4x [[https://www.mouser.at/ProductDetail/Lumex/SSL-LX30FT4GD?qs=sGAEpiMZZMuCm2JlHBGefjo7mRik%2FjcaResH8h9wozw%3D|Round 3mm Thruhole LEDs-GREEN-Flat]] | ||
+ | \\ | ||
+ | And there will be some additional Fasting Material, like bolts, Screws, Standoffs, that i dont know right now, because the first protoype has to be built first...\\ | ||
====== Frontpanel====== | ====== Frontpanel====== | ||
- | {{:phatline:Frontpanel.jpg?700|}}\\ | + | {{:phatline:Euro-LoopA-Frontpanel-growing.jpg?900|}}\\ |
- | I made a DXF File which you can send to [[https://www.formulor.de/|Formulor in Germany]]\\ | + | **I made a DXF File which you can send to:** (once the prototypestate is gone)\\ |
- | + | [[https://www.formulor.de|Formulor in Germany]] - Acrylic ... 2Pieces incl shipping 42€\\ | |
- | i panalized it so there are 2 Plates in it\\ | + | [[https://shop.frontpanels.de/custom-panels|frontpanels.de in germany]] my choose\\ |
- | I payed 40€ summed for booth plates incl shipping from Germany to Austria\\ | + | [[https://thebeast.co.uk/2d/|The Beast - UK]]\\ |
- | {{:phatline:2xLRE-OLED-BAR-DXF.zip?700|}}\\ | + | [[https://www.schaeffer-ag.de/en/|Schaeffer-ag.de]] |
+ | \\ | ||
**Recommend Material**\\ | **Recommend Material**\\ | ||
- | 3mm x 128.5 x 188.58 Aluminium, anodised)\\ | + | 2mm x 128.5 x 188.58 Aluminium, anodised\\ |
+ | contact frontpanels: info@frontpanels.de\\ | ||
+ | {{:phatline:Frontpanels-Euroloopa.zip?900|}} - NOT TESTET - REVERSE ENGENEERING!!!!!!\\ | ||
+ | ====== Interconnection to LoopA ====== | ||
+ | To most connections are Midi... so before start, take a look at some standards:\\ | ||
+ | {{:phatline:Midi-Type-A.jpg?900|}}\\ | ||
====== To Do ====== | ====== To Do ====== |