loopa-eurorack-panel
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| loopa-eurorack-panel [2022/01/16 04:37] – phatline | loopa-eurorack-panel [2022/02/24 21:27] (current) – phatline | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== LoopA - Eurorack - Frontpanel with breakout PCB ====== | ====== LoopA - Eurorack - Frontpanel with breakout PCB ====== | ||
| - | {{: | + | {{: |
| - | {{: | + | {{: |
| - | **I made this PCBs to use it with Fairlightii´s | + | {{youtube> |
| + | **I made this Breakout-PCB and Frontpanel for the midiphy LoopA [[https:// | ||
| - | **4x PCBs on one 100x100mm**\\ | + | **PCB Size is 172x24mm**\\ |
| - | there is no V-Groove, you have to cut it on the marking\\ | + | You have to decide if you want Midi Out 3 or the Gate OUT (space thing)\\ |
| - | groove it on top and back, with a new sharp cutter, do it several times, then break it\\ | + | The Reset Switch |
| - | {{: | + | If you want use the PCB you dont have place for the stock DIN Sockets!\\ |
| - | With this Method you pay for 20 PCBs 8€ all inclusive to EU-Austria\\ | + | |
| - | So you can Stuff 5 LRE8x2 with this.\\ | + | |
| - | Here are the gerberfiles for production - testet on [[https:// | + | |
| - | {{: | + | |
| - | {{: | + | |
| - | ====== Hardware Requirements ====== | + | |
| - | * a MIOS32 Core to connect too\\ | + | |
| - | * Soldering Iron - with a Dip that can Handle Thruhole-Parts, | + | |
| - | * LRE8x2 | + | |
| - | ====== Shematic ====== | + | {{: |
| - | {{: | + | {{: |
| - | **Full**: | + | |
| - | ====== Building and BOM====== | + | ON this board we have 3 micromatch Connectors, which are crimped fast on a cable\\ |
| - | The Values | + | On the other side of the cable you have to solder directly to the Base-PCB,\\ |
| + | be carefull while soldering - and follow the shematic, which is layout for 3.5 Jack Midi Type B!\\ | ||
| + | {{: | ||
| + | {{: | ||
| - | **Following Quantity is for 4 PCBs:**\\ | ||
| - | 8x 1Row 7Pin headers (2.54mm pitch)\\ | ||
| - | 8x 1K 1208 SMD Resistors\\ | ||
| - | 12x 10uF 1208 Capacitors (non polarized)\\ | ||
| - | 3x 10K 0603 SMD Resistors which are optional\\ | ||
| - | {{: | ||
| - | 8x 0.96" SSD1306 Screens\\ | + | ====== Hardware Requirements ====== |
| - | {{:phatline: | + | |
| + | * Soldering Iron - with a Dip that can Handle Thruhole-Parts, | ||
| + | * The other Parts from the BOM\\ | ||
| - | ====== | + | ====== |
| - | {{: | + | All necessery Information is printet on the PCB, but also check the Shematic...\\ |
| - | I made a DXF File which you can send to [[https:// | + | |
| - | i panalized it so there are 2 Plates in it\\ | + | 5x [[https:// |
| - | I payed 40€ summed | + | 3x [[https:// |
| - | {{:phatline:2xLRE-OLED-BAR-DXF.zip?700|}}\\ | + | 6x [[https:// |
| + | 1x [[https:// | ||
| + | 1x [[https:// | ||
| + | 8x [[https:// | ||
| + | 12x [[https:// | ||
| + | 4x [[https:// | ||
| + | \\ | ||
| + | And there will be some additional Fasting Material, like bolts, Screws, Standoffs, that i dont know right now, because the first protoype has to be built first...\\ | ||
| - | **Recommend Material from Formulor: | + | ====== Frontpanel====== |
| - | 3mm Acrylglas GS 384x384mm, mittelgrau transparent(7C83)\\ | + | {{: |
| + | **I made a DXF File which you can send to:** (once the prototypestate is gone)\\ | ||
| + | [[https:// | ||
| + | [[https:// | ||
| + | [[https:// | ||
| + | [[https:// | ||
| + | \\ | ||
| + | **Recommend Material**\\ | ||
| + | 2mm x 128.5 x 188.58 Aluminium, anodised\\ | ||
| + | contact frontpanels: | ||
| + | {{: | ||
| + | ====== Interconnection to LoopA ====== | ||
| + | To most connections are Midi... so before start, take a look at some standards: | ||
| + | {{: | ||
| ====== To Do ====== | ====== To Do ====== | ||
| - | waiting for christmas... | + | waiting for the PCBs and Panels... since the Panels are reverse - engineered - its praying for good luck!\\ |
| ====== Community users working on it ====== | ====== Community users working on it ====== | ||
| - | * **[[Phatline]]** = PCB & Shematic, UI-Programming, Documentation...\\ | + | * **[[Phatline]]** = PCB & Shematic, Documentation...\\ |
| Just let a Private message on the forum to user already involved.\\ | Just let a Private message on the forum to user already involved.\\ | ||
loopa-eurorack-panel.1642307866.txt.gz · Last modified: 2022/01/16 04:37 by phatline