acsensorizer
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| acsensorizer [2006/10/15 09:35] – (old revision restored) 127.0.0.1 | acsensorizer [2011/07/11 23:17] (current) – admin | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ======= AC Sensorizer ======= | ======= AC Sensorizer ======= | ||
| - | ====== Description ===== | + | [[audiocommander|{{ |
| - | **//AC Sensorizer sensorizes up to 8 sensors and interpolates its AIN-readings. | ||
| - | The main target of this application are sensoric devices delivering not exactly | ||
| - | 0 - 5 V, like pressure-, distance-, resistor-based sensors or softPots.// | ||
| - | |||
| - | :!:\\ | ||
| - | This is a preliminary beta-release.\\ | ||
| - | Use and build at your own risk!\\ | ||
| - | There will be major improvements in the GUI/HUI within the release of the next version. Though the code basis (ACSensorizer.c) won't probably change that much... | ||
| - | // -- audiocommander// | ||
| - | |||
| - | |||
| - | {{http:// | ||
| - | {{http:// | ||
| - | {{http:// | ||
| - | {{http:// | ||
| - | {{http:// | ||
| - | {{http:// | ||
| - | {{http:// | ||
| - | {{http:// | ||
| - | |||
| - | Picture Gallery: http:// | ||
| \\ | \\ | ||
| - | |||
| - | {{http:// | ||
| - | {{http:// | ||
| - | |||
| - | Demo-Video 1: http:// | ||
| - | Demo-Video 2: http:// | ||
| - | |||
| - | audicommander' | ||
| - | |||
| - | Note: \\ | ||
| - | //The Sensorizer is attached to a Computer which converts the Controller Messages – produced by the Sensorizer – to harmonized and clock-synchronized Note-Signals. I'm using Absynth Sounds ...but due to the buggy versions and ugly customer support from NI, I discourage everyone using NI-products :( As soon as I have enough money, I'll switch to Virus :) // | ||
| - | |||
| \\ | \\ | ||
| - | + | [[acsensorizer_04|{{ac:sensorizer_mini_3d_front.jpg}}]] [[acsensorizer_basic|{{http://www.audiocommander.de/ | |
| - | ===== Features ===== | + | [[acsensorizer_04|ACSensorizer v0.4]], last release: 7/2007\\ |
| - | + | **Current Version** | |
| - | * supports up to 8 sensors, code can be adapted to use more (eg with PIC18F4620) | + | |
| - | * enable/ | + | |
| - | * slowdown: slows down the signal and increases the gaps between generated values | + | |
| - | * assignable CH and Controller-Number | + | |
| - | * sense-min: 10bit value, ignores every signal below | + | |
| - | * sense-max: 10bit value, ignores every signal above | + | |
| - | * sense-factor: | + | |
| - | * AUTO-sense feature: auto-calibration of sensor, detect MIN/MAX by sensing automatically adapts sense-factor! | + | |
| - | * scale from and scale to: scales the output value from/to | + | |
| - | * invert signal | + | |
| - | * pedal modes: | + | |
| - | * filter | + | |
| - | * panic | + | |
| - | * combinations of all pedal mode options are possible | + | |
| - | * detect release: send 0-value if signal drops below sense-min | + | |
| - | * bankstick support: 1 connected bankstick provides 2 banks with 127 patches each | + | |
| - | * midi configurable: | + | |
| - | * NRPN-MSB CC99 for sensorSelect | + | |
| - | * NRPN-LSB CC98 for controlType | + | |
| - | * DataEntry MSB CC6 and LSB CC38 for controlValue | + | |
| - | * LCD-Output (2x16 or -recommended- 4x20) | + | |
| - | * HUI-Input to control up to 4 sensors with 8 switch-encoders, pedal, store- & panic-button in 2 modes (PLAY/SETUP) | + | |
| - | * ACSim Console Debugger: code integrated and ready to use configured for XCode2 | + | |
| - | | + | |
| - | | + | |
| - | | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| \\ | \\ | ||
| - | ===== Required hardware===== | ||
| - | |||
| - | **MBHP Modules:** | ||
| - | * one MBHP_CORE module | ||
| - | * one MBHP_LCD module (5x20 optimized, 2x16 available) | ||
| - | * one MBHP_DIN module for | ||
| - | * 8 Encoders (preferrably with): | ||
| - | * 8 pushButtons | ||
| - | * 1 mode-select switch | ||
| - | * 1 pedal (optional) | ||
| - | * 1 PANIC button (optional) | ||
| - | * 1 STORE button (optional) | ||
| - | * 1 UP & 1 DOWN button (optional) | ||
| - | |||
| - | **Sensors: | ||
| - | * up to 8 (default: 4) sensors connected to unmuxed AIN (J5 of MBHP_CORE). Note that sensors 5 to 8 can only be configured via MIDI by sending NRPN-messages | ||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
| \\ | \\ | ||
| + | [[acsensorizer_02|{{http:// | ||
| + | < | ||
| + | **There will be no further developments based on this HUI-concept!** \\ | ||
| + | **It is strongly recommended to build v0.4 (more features, improved easy-to-use GUI)** | ||
| - | ====== Application Software ====== | ||
| - | * [[http:// | ||
| - | * [[http:// | ||
| \\ | \\ | ||
| - | //Version History// | ||
| - | * 0.2.2: | ||
| - | * initial release | ||
| - | * 0.2.3: | ||
| - | * removed MidiTrough and used MIOS_Merger | ||
| - | * some minor bugs | ||
| - | * two example miniAudicle/ | ||
| - | * 0.2.4: | ||
| - | * fixed severe bank select bug that prevented accessing even banks | ||
| - | |||
| - | \\ | ||
| - | //Compiling Notes// | ||
| - | |||
| - | The application can be recompiled with a variety of strictly separated #define- | ||
| - | options. For example setting SENSORIZER_INTERFACE_HUI to 0 compiles the application | ||
| - | without hardware input controls and therefore reduces the file- and application space. | ||
| - | Compiling without HUI, BANKSTICK, NRPN-Config and LCD generates code with approx. 3 or 4 pages; compiling with all options will result in an application file of approx. 12 to 14 pages. | ||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
| \\ | \\ | ||
| \\ | \\ | ||
| + | have fun! // -- audiocommander // | ||
| - | ====== MIDI-Controllable Parameters ====== | ||
| - | |||
| - | All Sensorizer parameters can be controlled and set by sending NRPN messages by MIDI: | ||
| - | |||
| - | 1. Send NRPN MSB (Controller# | ||
| - | 2. Send NRPN LSB (Controller# | ||
| - | 3. Send NRPN Data MSB (Controller# | ||
| - | |||
| - | \\ | ||
| - | ^ NRPN MSB | | | | | ||
| - | ^ CC ^ Value ^ Control Type ^ Note ^ | ||
| - | | CC99, 0x63 | 0..7 | Sensor 0..7 | See Table B | | ||
| - | | CC99, 0x63 | 126 | SysEx mode: ON | n/a | | ||
| - | | CC99, 0x63 | 127 | SysEx mode: OFF | n/a | | ||
| - | // Table A: Control Types// | ||
| - | |||
| - | \\ | ||
| - | ^ NRPN LSB | | ^ DATA ENTRY MSB/LSB | | | | ||
| - | ^ CC ^ Value ^ Control Parameter ^ CC ^ Value ^ Description ^ | ||
| - | | CC98, 0x62 | 0x00 | enabled | CC38, 0x26 | 0/1 | ON/OFF | | ||
| - | | CC98, 0x62 | 0x01 | pedalMode | CC38, 0x26 | 0..7 | FILTER/ | ||
| - | | CC98, 0x62 | 0x02 | autoSense | CC38, 0x26 | 0..2 | AUTOSENSE_OFF/ | ||
| - | | CC98, 0x62 | 0x03 | invert | CC38, 0x26 | 0/1 | 0..127 or 127..0 | | ||
| - | | CC98, 0x62 | 0x04 | releaseDetect | CC38, 0x26 | 0/1 | send 0 on release | | ||
| - | | CC98, 0x62 | 0x10 | slowdown | CC38, 0x26 |0..127 | drop AIN notifications | | ||
| - | | CC98, 0x62 | 0x11 | sense_min | CC38, 0x26 & CC6, 0x6 | 0..1023 | drop below and set sense minimum | | ||
| - | | CC98, 0x62 | 0x12 | sense_max | CC38, 0x26 & CC6, 0x6 | 0..1023 | drop above and set sense maximum | | ||
| - | | CC98, 0x62 | 0x13 | sense_factor | CC38, 0x26 | 0..64 | f=(range/ | ||
| - | | CC98, 0x62 | 0x21 | scale_from | CC38, 0x26 | 0..127 | restrict and rescale output | | ||
| - | | CC98, 0x62 | 0x22 | scale_to | CC38, 0x26 | 0..127 | restrict and rescale output | | ||
| - | | CC98, 0x62 | 0x70 | CH | CC38, 0x26 | 0..15 | MIDI Channel of sensor | | ||
| - | | CC98, 0x62 | 0x71 | CC | CC38, 0x26 | 0..127 | MIDI Controller Change Number of sensor | | ||
| - | // Table B: Control Parameters// | ||
| - | |||
| - | |||
| - | |||
| - | |||
| - | \\ | ||
| - | \\ | ||
| - | |||
| - | ====== HUI-Controllable Parameters ====== | ||
| - | |||
| - | :!: **The design of the Encoders is about to change with the next version. I just had one DIN at hand and the whole project had to be finished in time; with a second DIN and 4/5 more Encoders, everything will be a bit handier...** | ||
| - | |||
| - | If you build the Sensorizer with enabled HUI-mode, it provides configuration possibilities for 4 sensors. However, you could change the code easily to support all 8 sensors. | ||
| - | |||
| - | Used Hardware: | ||
| - | * 1 Mode-Switch button (PLAYMODE <-> SETUPMODE) | ||
| - | * 8 Encoders with Switch, two Encoders per sensor, the first row of encoders is called ENC_MIN, the lower ENC_MAX | ||
| - | * 4 Buttons (UP, DOWN, STORE, PANIC) | ||
| - | |||
| - | \\ | ||
| - | ^ Function ^ Encoder(s) ^ PLAYMODE ^ SETUP-MODE ^ | ||
| - | | Turn | ENC_MIN | ||
| - | | Turn | ENC_MAX | ||
| - | | Press & Turn | ENC_MIN | CH (MIDI Channel) | senseMin (10bit) | | ||
| - | | Press & Turn | ENC_MAX | CC (MIDI Controller) | senseMax (10bit) | | ||
| - | | | | | | | ||
| - | | Press | ENC_MIN + ENC_MAX | sensor ON | AUTOSENSE_MIN | | ||
| - | | Press | ENC_MAX + ENC_MIN | sensor OFF | AUTOSENSE_MAX | | ||
| - | | | | | | | ||
| - | | Press | PANIC + PEDAL | switch PEDALMODE (Mode 0 to 7) | | | ||
| - | | Press | PANIC + ENC_MAX | switch RELEASE DETECT (ON/OFF) | | | ||
| - | | Press & Turn | PANIC + ENC_MAX | senseFactor (0-32) | - | | ||
| - | // Table C: Encoder Controls// | ||
| - | |||
| - | |||
| - | \\ | ||
| - | \\ | ||
| - | |||
| - | ====== BANKSTICK Patch Description ====== | ||
| - | m5_sensorizer supports writing and reading to a connected bankstick.\\ | ||
| - | Each patch consists of 2 pages ˆ 64 bytes => 128 bytes\\ | ||
| - | 2 banks with 128 patches each are available per 1 connected bankstick | ||
| - | |||
| - | Sending a PRG_CH message in PLAYMODE [P] loads the corresponding patch.\\ | ||
| - | Sending a PRG_CH message in SETUPMODE[S] sets the corresponding patch without loading the patch data. Use this behavior to copy patches. | ||
| - | |||
| - | Choose the appropriate bank by sending a Coarse-Adjust Bankselect (CC#0).\\ | ||
| - | In HUI-Mode, switching a bank on the device also sends the current Bank/PRG.\\ | ||
| - | |||
| - | Memory-map of one patch:\\ | ||
| - | |||
| - | ^ Data ^ Size in Bytes = Sum ^ Page ^ Address | ||
| - | | Version | ||
| - | | PatchName | ||
| - | | < | ||
| - | | sensor[8] | ||
| - | | CH[8] | 08 = 40 | 1 | 32 @ 0x20 | | ||
| - | | CC[8] | 08 = 48 | 1 | 40 | | ||
| - | | < | ||
| - | | | | | | | ||
| - | | slowdown[8] | ||
| - | | sense_factor[8] | 08 = 16 | 2 | 8 | | ||
| - | | sens_min[8].MSB | 08 = 24 | 2 | 16 @ 0x10 | | ||
| - | | sens_min[8].LSB | 08 = 32 | 2 | 24 | | ||
| - | | sens_max[8].MSB | 08 = 40 | 2 | 32 @ 0x20 | | ||
| - | | sens_max[8].LSB | 08 = 48 | 2 | 40 | | ||
| - | | scale_from[8] | ||
| - | | scale_to[8] | ||
| - | // Table D: Bankstick Patch Content// | ||
| - | |||
| - | Patch addresses are: (patch * 0x80)\\ | ||
| - | or PIC-optimized: | ||
| - | |||
| - | \\ | ||
| - | Example hex-output of patch#0: | ||
| - | |||
| - | < | ||
| - | **MIOS_BANKSTICK_WritePage at 0x0 | ||
| - | 0: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ | ||
| - | 16: 00 00 00 00 00 00 00 00 80 80 80 80 40 08 00 00 ............@... | ||
| - | 32: 00 00 00 00 04 04 04 04 14 15 16 17 00 00 00 00 ................ | ||
| - | 48: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ | ||
| - | |||
| - | **MIOS_BANKSTICK_WritePage at 0x40 | ||
| - | 0: 08 08 08 08 00 00 00 00 04 04 04 04 00 00 00 00 ................ | ||
| - | 16: 00 00 00 00 7f 00 00 00 40 40 40 40 7f 00 00 00 ........@@@@.... | ||
| - | 32: 03 03 03 03 00 00 00 00 70 70 70 70 40 40 40 40 ........pppp@@@@ | ||
| - | 48: 00 00 00 00 00 00 00 00 7f 7f 7f 7f 00 00 00 00 ................ | ||
| - | </ | ||
| - | |||
| - | |||
| - | |||
| - | \\ | ||
| - | \\ | ||
| - | \\ | ||
| - | More details can be found in the readme.txt!\\ | ||
| - | This site is about to change while the Sensorizer is beeing developed further!\\ | ||
| - | |||
| - | have fun! // -- audiocommander // | ||
acsensorizer.1160904901.txt.gz · Last modified: 2006/11/06 11:06 (external edit)