home:mbhp:module:din
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| home:mbhp:module:din [2008/12/02 20:03] – Just Phil | home:mbhp:module:din [2008/12/20 01:45] (current) – Fixed link stryd_one | ||
|---|---|---|---|
| Line 5: | Line 5: | ||
| ===== Getting Started ===== | ===== Getting Started ===== | ||
| - | * [[: | + | * [[: |
| * [[: | * [[: | ||
| Line 16: | Line 16: | ||
| * [[: | * [[: | ||
| * etc | * etc | ||
| - | |||
| - | |||
| ===== Details ===== | ===== Details ===== | ||
| + | |||
| === Pins === | === Pins === | ||
| [[din_dout_pin_list | DIN & DOUT pin table]] | [[din_dout_pin_list | DIN & DOUT pin table]] | ||
| + | |||
| + | |||
| + | |||
| + | ===Available Ports=== | ||
| + | |||
| + | Following interfaces are provided by the dinx4 module: | ||
| + | |||
| + | | Name ^No. of pins ^Description | | ||
| + | ^J1 |5 |Interface to CORE J9 (if buttons are used) and CORE J6 (if encoders are used, MIDIbox16E only). DINX4 J1 provides two power pins for 5V, 0V, the serial clock, the latch enable and the serial output of the register chain. This port can also be connected with J2 of another DINX module.| | ||
| + | ^J2 |5 |Interface to another DINX4 module. DINX4:J2 provides nearly the same pins like J1, just only the serial output of the first IC is replaced by the serial input of the last IC. This port can be connected with J1 of another DINX module.| | ||
| + | ^J3 to J9 |5 |These are the digital input lines, every connector comes with 4 of them and an additional pin for ground. See mbhp_dinx4_32buttons.pdf as an example how to connect buttons to these pins, and mbhp_dinx4_16enc.pdf how to connect rotary | | ||
| === PCB files === | === PCB files === | ||
| - | | + | |
| + | |||
| + | * [[http:// | ||
| + | |||
| + | * [[http:// | ||
| + | |||
| + | * [[http:// | ||
| === Schematic === | === Schematic === | ||
| - | | + | |
| + | |||
| + | * [[http:// | ||
| === List of parts === | === List of parts === | ||
| - | | + | Here are suggested part numbers for various distributors for parts for the DIN board. If you find another site or dealer with a different parts list feel free add it into the list. Also if you’ve successfully used a different part from what was listed here please add the number and/or link to the list. |
| + | | Part Name ^ Description ^ Polar ^ soldering temp ^ QTY ^ [[http:// | ||
| + | ^ IC1-IC4 | 74HC165 | Yes | Don' | ||
| + | ^ R1-R36 | Resistor 10 kOhm | No | ??? | ||
| + | ^ C1-C4 | Ceramic Cap 100 nF | No | ??? | ||
| + | ^ - | IC-Sockets for serial registers | Yes | ??? | ||
| + | ^ J* | 1-row SIL Headers (50 pins) | No | ??? | ||
| + | ^ - | 1-row sil female con | No | ??? | ||
| + | ^ - | Ribbon cable 3 meters | No | ??? | ||
| Line 37: | Line 65: | ||
| ==== Building instructions ==== | ==== Building instructions ==== | ||
| blah blah blah | blah blah blah | ||
| - | |||
| ==== Connection to Core Module ==== | ==== Connection to Core Module ==== | ||
| Line 46: | Line 73: | ||
| \\ | \\ | ||
| + | |||
| + | ==== Connecting Input Devices ==== | ||
| + | [[http:// | ||
| + | [[http:// | ||
| + | [[http:// | ||
| + | [[http:// | ||
| ==== Testing ==== | ==== Testing ==== | ||
| Line 87: | Line 120: | ||
| ===Reference=== | ===Reference=== | ||
| - | |||
home/mbhp/module/din.1228248188.txt.gz · Last modified: 2008/12/02 20:03 by Just Phil