mbhp_genesis
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| mbhp_genesis [2017/02/10 03:44] – [Notes about the YM2612's Test pin] sauraen | mbhp_genesis [2023/09/05 04:19] (current) – [Component stuff chart] sauraen | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | {{http:// | + | {{http:// |
| ====== Summary ====== | ====== Summary ====== | ||
| Line 141: | Line 141: | ||
| | 1 | Y2 or Y4 | 3.58 MHz (or 4 MHz) oscillator | 520-TCH357-X | Oscillator (either half-size/ | | 1 | Y2 or Y4 | 3.58 MHz (or 4 MHz) oscillator | 520-TCH357-X | Oscillator (either half-size/ | ||
| | 3 | Q1, Q2, Q3 | 2N7000 or BS170 | 821-TSM2N7000KC821-T or 512-BS170 | Any small-signal N-channel MOSFET with the gate as the center pin; the board silkscreen is for 2N7000, if you use BS170 (as I did) mount them backwards to match the source and drain pins. | | | 3 | Q1, Q2, Q3 | 2N7000 or BS170 | 821-TSM2N7000KC821-T or 512-BS170 | Any small-signal N-channel MOSFET with the gate as the center pin; the board silkscreen is for 2N7000, if you use BS170 (as I did) mount them backwards to match the source and drain pins. | | ||
| - | | - | J1, J2, J5, J6, J7, J8 | 0.1" pin headers | Buy in bulk | Headers; J1, J2, and J7 connect all boards together, so put sockets on one side of the boards and have the pins sticking | + | | - | J1, J2, J7, J10 | 0.1" |
| - | | - | J10 | 0.1" | + | | - | J5, J6, J8 | 0.1" pin headers | Buy in bulk | Headers; |
| | 1 | L1 | 10 uH inductor | 434-SMCCN-100K-02 | For LC filter for analog power rail | | | 1 | L1 | 10 uH inductor | 434-SMCCN-100K-02 | For LC filter for analog power rail | | ||
| | 2 | C12, C13 | 100 uF electrolytic | Buy in bulk | Power rail filter caps | | | 2 | C12, C13 | 100 uF electrolytic | Buy in bulk | Power rail filter caps | | ||
| Line 174: | Line 174: | ||
| The values I used for my quad builds are on the schematic and in the parts list. The normal values are for use with YM2612s, and the values in parentheses are the ones to use with YM3438s. All other parts which just show one value are the same on both builds. | The values I used for my quad builds are on the schematic and in the parts list. The normal values are for use with YM2612s, and the values in parentheses are the ones to use with YM3438s. All other parts which just show one value are the same on both builds. | ||
| ===== Component stuff chart ===== | ===== Component stuff chart ===== | ||
| - | Here is a chart of what components should be stuffed on each build configuration I could think of. In most cases, several of these build configurations will be active at the same time (e.g. in a typical four-board setup, the top board is A, B or C, D, (E), F, G, H, I, M). | + | Here is a chart of what components should be stuffed on each build configuration I could think of. In most cases, several of these build configurations will be active at the same time (e.g. in a typical four-board setup, the top board is A, B or C, D, (E), F, G, H, I, M. Note that MIDIbox Quad Genesis requires F, G, H, I). |
| ^ Label ^ Description ^ | ^ Label ^ Description ^ | ||
| Line 197: | Line 197: | ||
| ^ Parts ^ A ^ B ^ C ^ D ^ E ^ F ^ G ^ H ^ I ^ J ^ K ^ L ^ M ^ N ^ O ^ P ^ | ^ Parts ^ A ^ B ^ C ^ D ^ E ^ F ^ G ^ H ^ I ^ J ^ K ^ L ^ M ^ N ^ O ^ P ^ | ||
| - | | U1, C1, C14, C15, Y1 or Y3, C20, C21, R11, R12, R15, R16, C23, C24, R18, R19, R21, R22 | X | | + | | U1, C1, C14, C15, Y1 or Y3, C20, C21, R11, R12 | X | |
| | R8, R9 | | X | | | R8, R9 | | X | | ||
| | R33, R34 | | | R33, R34 | | ||
| - | | U2, C2, Y2 or Y4, U10, C10, Q2, Q3, R4:6, R10, C22, R13, R14, R17, C25, R20, R23, R24 | | + | | U2, C2, Y2 or Y4, U10, C10, Q2, Q3, R4:6, R10, C22, R13 | |
| - | | J1, C12, L1, C13, C11, U4, C4, C16, R31, R32, C18, C19, U5, C5, C17, R25, R26, C29, C30, C31, C32, R27:30, J8 | | + | | J1, C12, L1, C13, C11 | X | |
| | J6, R7 | | | J6, R7 | | ||
| | U7, C7 | | | U7, C7 | | ||
| | U8, C8 | | | U8, C8 | | ||
| | U6, C6, Q1, R1 | | | U6, C6, Q1, R1 | | ||
| - | | U9, C9, C26: | + | | U9, C9 | |
| | J5 | | | J5 | | ||
| | Short U3:5 to U3:15 | | | Short U3:5 to U3:15 | | ||
| Line 212: | Line 212: | ||
| | Short U8:3 to U8:6 | | | Short U8:3 to U8:6 | | ||
| | U3, C3, J2 | | | U3, C3, J2 | | ||
| + | | U4, C4, U5, C5, C16:19, C23:32, R15:32, J8 | | ||
| | Short U3:13 to J3:2, short U3:12 to J3:1 | | | Short U3:13 to J3:2, short U3:12 to J3:1 | | ||
| | Short U3:11 to J3:2, short U3:10 to J3:1 | | | Short U3:11 to J3:2, short U3:10 to J3:1 | | ||
| Line 234: | Line 235: | ||
| For the OPN2 chips, the YM3438 is a complete reimplementation of the YM2612 in CMOS instead of NMOS. They also changed the output stage to get rid of some analog error in the YM2612' | For the OPN2 chips, the YM3438 is a complete reimplementation of the YM2612 in CMOS instead of NMOS. They also changed the output stage to get rid of some analog error in the YM2612' | ||
| + | |||
| + | (Note about the next two paragraphs: the resistor values given in the parts list are the ones I used and tested for each of YM2612 and YM3438, there' | ||
| The differences for this module are relatively simple. For a YM2612, the audio outputs require a known load to perform to spec--these are R8 and R9. The value of 2.2k was taken from the [[http:// | The differences for this module are relatively simple. For a YM2612, the audio outputs require a known load to perform to spec--these are R8 and R9. The value of 2.2k was taken from the [[http:// | ||
mbhp_genesis.1486698274.txt.gz · Last modified: 2017/02/10 03:44 by sauraen