Differences

This shows you the differences between two versions of the page.

--- mididocs:seq:launchpadblm [2014/09/15 01:36] – [SETUP] borfo
+++ mididocs:seq:launchpadblm [2014/09/15 18:05] (current) – borfo
@@ Line 1: / Line 1: @@
 **[[mididocs:index|MIDIdocs]]**
 ====== Novation Launchpad Button LED Matrix (BLM) ======
+[[http://midibox.org/forums/topic/19031-mididocs-novation-launchpad-blm-discussion-thread/|Forum Discussion Thread]] - for comments, corrections, or questions about this article
-[[http://midibox.org/forums/topic/13137-midibox-seq-v4-release-feedback/?p=166238|Link to Forum Discussion]]
+Since firmware version 87, the SEQ V4 supports the use of two [[http://global.novationmusic.com/midi-controllers-digital-dj/launchpad|Novation Launchpads]] as a [[http://ucapps.de/midibox_seq_manual_blm.html|BLM control surface.]]  Two Launchpads form a 16x8+X BLM, and up to four can be connected to make a full 16x16+X control surface.
-Since firmware version 87, the SEQ V4 supports the use of two Novation Launchpads as a [[http://ucapps.de/midibox_seq_manual_blm.html|BLM control surface.]]  Two Launchpads form a 16x8+X BLM, and up to four can be connected to make a full 16x16+X control surface.
 The Launchpad BLM is implemented as a feature of the JUCE-based BLM emulator software.  The launchpads don't connect to the SEQ directly.  Instead, they connect to a computer running the JUCE BLM emulator - the emulator software acts as a translator, converting the BLM Protocol sysex messages into midi signals to light the LEDs on the Launchpad, and translating button presses on the Launchpad into a format the SEQ can understand.
+This has been tested with the Novation Launchpad Mini.  Presumably, the Launchpad S should work as well, since they're essentially the same controller.  The original launchpad hasn't been tested.  If you have one, try it and post a comment in the forums to let us know if it works.
 Support for button grid controllers other than the launchpad may be possible in the future.
+{{http://www.ucapps.de/midibox_seq/mbseq_novation_launchpad_mini.jpg}}
 =====SETUP=====
@@ Line 23: / Line 26: @@
   - Open the Virtual BLM emulator software.
   - If you're using two Launchpads, select "16x8+X" in the layout dropdown menu.  If you're using 4, select "16x16+X".
-  -
+  - In the MIDI IN and MIDI OUT dropdown menus, select the USB port you chose as the "BLM Scalar Port" on your SEQ V4.
+  - The OSC settings can be left blank.
+  - Press the "Ext. Controller" button.
+  - Select "Novation Launchpad" in the "Controller" dropdown.
+  - Select your two or four launchpads in the MIDI IN and OUT dropdowns.
+  - The "Rotation Settings" dropdown allows you to rotate the launchpads by 90 degree increments.  Using two launchpads, set the first to "270 Degree" and the second to "0 Degree" in order to set the launchpads up as shown in the picture above.
+...and you're done!
+=====Resources=====
+[[http://midibox.org/forums/topic/13137-midibox-seq-v4-release-feedback/?p=166238|Link to forum thread where this feature was introduced]]