Differences

This shows you the differences between two versions of the page.

--- speakjet_control_overview [2006/06/11 14:05] – created audiocommander
+++ speakjet_control_overview [2006/12/05 14:03] (current) – Removed progress-note, document is up-to-date. audiocommander
@@ Line 1: / Line 1: @@
 \\
-:!: **THIS DOCUMENT IS CURRENTLY UNDER CONSTRUCTION** :!:
-\\
+Because the information in the SpeakJet Manual is relatively wide spreaded, this page gives a quick overview of the control possibilities of the Speakjet:
 \\
 ====== MSA (Mathmatical Sound Architecture) ======
 MSA commands are stored in the 64-Byte input buffer and are executed in the order they are received.
 ===== MSA Controls =====
+An 'X' indicates that a second number should follow as parameter.
-==== Pause ====
+==== Pause Control ====
 : Pause 0 ms\\
 : Pause 100 ms\\
@@ Line 20: / Line 20: @@
 : Pause 90 ms\\
-: Wait\\
+: Wait // Watch out! Waits for event input line or SCP-Start command!//\\
+: Delay, X // number of 10 ms intervals to delay before continuing on to the next code, accepts 0-255//\\
-==== Next Sound ====
+==== Next Sound Control ====
 : Play next sound fast\\
 : Play next sound slow\\
@@ Line 30: / Line 30: @@
 : Play next sound low\\
-====
+==== Volume/Pitch/Speed/Bend Control ====
+: Volume, X // sets Master Volume Level, accepts 0-127//\\
+: Speed, X // Play Speed, default 114, accepts 0-127//\\
+: Pitch, X // Pitch in Hertz, only for voiced sounds, default 88, accepts 0-255 (=32kHz..240kHz)//\\
+: Bend, X // Sets the Frequency Band (from deep hollow to high metallic), default 5, accepts 0-15//\\
+==== Port Control ====
+: PortCtr, X // binaurally encoded output line control, see manual for details, default 7, accepts 0-7//\\
+: Port, X // port output value, see manual for details, default 0, accepts 0-7//\\
+==== Phrase Control ====
+: Repeat, X // repeats the next code x-times, accepts 0-255//\\
+: Call Phrase, X // which EEPROM phrase to play, max 3 level deep nesting//\\
+: Goto Phrase, X // which EEPROM phrase to play//\\
+: End of Phrase
+==== Reset ====
+: Reset Defaults
+\\
+===== MSA Sound Codes =====
+..254: MSA Sound Phrases and Effects, see [[SpeakJet Definition List]].
+\\
+\\
+====== SCP (Serial Control Protocol) ======
+SCP commands are executed immediately and provide control over the 5-channel synthesizer as well as accessing the internal speakjet EEPROM.
+\\
+===== Entering SCP =====
+'\0' to enter SCP
+==== SCP Commands ====
+'H': Store Memory Type //accepts 0 and 32//\\
+  * '0H': Write a register's value\\
+  * '32H': Write to the internal EEPROM\\
+'J': Memory Address\\
+  * '0J': Envelope Freq\\
+  * '1J': OSC1 Freq .. '5J': OSC5 Freq\\
+  * '6J': Distortion\\
+  * '7J': Master Volume\\
+  * '8J': Envelope Control\\
+  * '11J': OSC1 Vol .. '15J': OSC5 Vol\\
+'N': Store Memory\\
+'R': Clear Buffer\\
+'S': Stop Enounciating\\
+'T': Start Enounciating\\
+'V': ACK\\
+'W': Hard Reset\\
+\\
+===== Exiting SCP =====
+'X' or '\A'\\
+\\
+===== Examples =====
+\0 V X*\\
+//Enters SCP-Mode, enounciates READY and exits SCP-mode//
+J 0N 1J 500N 11J 16N*\\
+//1st OSC freq 500 and vol 16//
+J 32H 01N*\\
+//write 0x1 to the first location of internal EEPROM//
+J 00N*\\
+//set env-type to SAW//
+J 10N*\\
+//set env-type to TRIANGLE//
+//* Don't send spaces, this is just for readability!//