16x4blm_pcb
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
16x4blm_pcb [2013/02/28 14:47] – [Overview] ilmenator | 16x4blm_pcb [2022/06/17 09:56] (current) – [Where to buy?] ilmenator | ||
---|---|---|---|
Line 8: | Line 8: | ||
===== Overview ===== | ===== Overview ===== | ||
- | The board holds all necessary components including surface mount shift registers (DOUT and DIN) on the backside and connects via a single 10pin cable to J2 on Wilba' | + | The board holds all necessary components including surface mount shift registers (DOUT and DIN) on the backside and connects via a single 10pin cable to J2 on Wilba' |
- | The buttons do not align with Wilba' | + | The buttons do not align with Wilba' |
===== Schematic ===== | ===== Schematic ===== | ||
Line 26: | Line 26: | ||
The total size of the PCB is 335.15mm x 97.92mm. | The total size of the PCB is 335.15mm x 97.92mm. | ||
+ | |||
+ | ===== PCB Layout v2.0 ===== | ||
+ | Meanwhile, I have created a version 2 of the board, which basically has all the features of the original one, plus it can hold three different types of switches: | ||
+ | |||
+ | - the Marquardt 6425 series (my favourite switches) | ||
+ | |||
+ | - ITT Schadow D6 series (TK's favourite switches) | ||
+ | |||
+ | - E-Switch 612-TL1100 series (the ones that Wilba used on the SEQ v4 board). | ||
+ | |||
+ | {{: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ==== Where to buy? ==== | ||
+ | If you are interested in building this, send a personal message (PM) to user // | ||
===== BOM ===== | ===== BOM ===== | ||
Line 39: | Line 55: | ||
| R1-R32 | 1/4W resistor | | 220 | 32 | | 1/4W 220 | | | | R1-R32 | 1/4W resistor | | 220 | 32 | | 1/4W 220 | | | ||
| R33, R34 | 1/4W resistor | | 10k | 2 | | 1/4W 10K | | | | R33, R34 | 1/4W resistor | | 10k | 2 | | 1/4W 10K | | | ||
- | | SW1-SW64 | push switch | Marquardt 6425.0101* | | 64 | 979-6425.0101 | | [[http:// | + | | SW1-SW64 | push switch | Marquardt 6425.0101* | | 64 | 979-6425.0101 | TASTE 6425.0101 |
- | | | key cap | Marquardt 826.000.011 | 16x16mm | 64 | | | [[http:// | + | | | key cap | Marquardt 826.000.011 | 16x16mm | 64 | |TASTE S 826 (red!) |
- | | U1-U6 | 74HC595 | SO16 | | 6 | | SMD HC 595 | | | + | | U1-U6 | 74HC595 | SO16 | | 6 | 863-MC74HC595ADG |
| U7, U8 | 74HC165 | SO16 | | 2 | 863-MC74HC165ADR2G | | | | | U7, U8 | 74HC165 | SO16 | | 2 | 863-MC74HC165ADR2G | | | | ||
| J1, J2 | connector 2x5 | | | 2 | | WSL 10G | | | | J1, J2 | connector 2x5 | | | 2 | | WSL 10G | | | ||
Line 51: | Line 67: | ||
===== Frontpanel ===== | ===== Frontpanel ===== | ||
- | I have had my frontpanel laser cut by [[https:// | + | I have had my frontpanel laser cut at [[http:// |
{{: | {{: |
16x4blm_pcb.1362062874.txt.gz · Last modified: 2013/02/28 14:47 by ilmenator