antixfm
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision Last revision Both sides next revision | ||
|
antixfm [2016/07/14 17:33] psykhaze created |
antixfm [2016/07/14 17:46] psykhaze |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Antix Midibox FM Build ====== | ====== Antix Midibox FM Build ====== | ||
| - | {{ ::antix:mbfm_comp1.jpg?direct&600 |}} | + | {{ ::antix:mbfm_comp1.jpg?direct&650 |}} |
| ===== Introduction ===== | ===== Introduction ===== | ||
| + | |||
| + | {{ ::antix:mbfm_interior.jpg?direct&300|}} | ||
| I used MDF wood for the bottom and for the sides I used plywood with Zebrano veneer. | I used MDF wood for the bottom and for the sides I used plywood with Zebrano veneer. | ||
| The front and the rear panels are aluminium and a friend of mine made lasercutting in his workshop ( I designed it with Front Panel designer )then silkscreen ( an other friends in another workshop ) and at the end a layer of transparent acrylic. | The front and the rear panels are aluminium and a friend of mine made lasercutting in his workshop ( I designed it with Front Panel designer )then silkscreen ( an other friends in another workshop ) and at the end a layer of transparent acrylic. | ||
| + | |||
| + | {{::antix:zebrano_wood_cheeks.jpg?direct&400 |}} | ||
| The first problems was the long long time to wait the chips from Wilba because of the postal service.Wilba shipped to me the very next day but the parcel probably flight all around the world. | The first problems was the long long time to wait the chips from Wilba because of the postal service.Wilba shipped to me the very next day but the parcel probably flight all around the world. | ||
| The second crap was that my wife made crash on the floor the MB during the construction so the metal case has a little invisible dent. | The second crap was that my wife made crash on the floor the MB during the construction so the metal case has a little invisible dent. | ||
| + | {{ ::antix:rough_panel.jpg?direct&300|}} | ||
| + | |||
| + | |||
| ===== Setup ===== | ===== Setup ===== | ||
| Line 17: | Line 24: | ||
| The power supply is made by me with PCB etching and a good quality transformer ( the capacitors are high quality with low SR from railway technology ) | The power supply is made by me with PCB etching and a good quality transformer ( the capacitors are high quality with low SR from railway technology ) | ||
| - | ===== Photos ===== | + | {{::antix:pwr_supply.jpg?direct&400 |}} |
| - | + | \\ | |
| + | \\ | ||
| + | \\ | ||
| + | \\ | ||
| + | ===== Further Photos ===== | ||
| + | \\ | ||
| + | \\ | ||
| + | {{::antix:mbfm3.jpg?direct&800|}} | ||
| + | {{::antix:mbfm4.jpg?direct&800|}} | ||
| + | {{::antix:mbfm6.jpg?direct&800|}} | ||
| + | {{::antix:mbfm_comp3.jpg?direct&800|}} | ||
| + | {{::antix:mbfm_comp2.jpg?direct&800|}} | ||
| + | {{::antix:opl3.jpg?direct&800|}} | ||
antixfm.txt · Last modified: 2016/07/14 17:48 by psykhaze
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
