coilwinder
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
coilwinder [2023/04/02 20:10] phatline [Shemata] |
coilwinder [2023/04/03 23:40] (current) phatline |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Coil Winder ====== | ====== Coil Winder ====== | ||
| - | **REAL:**\\ | + | **A Tesla Coil winding machine, controlled by Mios:**\\ |
| - | {{:phatline:tm4-perspektive-l.hd-.jpg?700|}}\\ | + | {{phatline:Coil-Winder-Foto.jpg?900|}}\\ |
| \\ | \\ | ||
| + | Watch German Video about using it, and TimeLapse build\\ | ||
| + | {{youtube>z74-LL6L-BU}}\\ | ||
| + | \\ | ||
| + | Watch English Video... | ||
| + | {{youtube>NtUlX4rdx-k}}\\ | ||
| + | |||
| ===== CODE, FIRMWARE ===== | ===== CODE, FIRMWARE ===== | ||
| Line 26: | Line 32: | ||
| The Rest is stated in the youtube video, in TimeLapse\\ | The Rest is stated in the youtube video, in TimeLapse\\ | ||
| You can use any motor you like, the code is programmed for a Motor that takes 400 steps for a whole 360° turn... if you use other motors you need to adapt the code (which you can download a bit above...)\\ | You can use any motor you like, the code is programmed for a Motor that takes 400 steps for a whole 360° turn... if you use other motors you need to adapt the code (which you can download a bit above...)\\ | ||
| + | |||
| + | ==== Main Parts ==== | ||
| + | **Midibox**: | ||
| + | Core STM32 based core (STM32F4)\\ | ||
| + | DINX4 Module (only 3DINX are used)\\ | ||
| + | Levelshifter circuit from 3to5Vs (J10A to Motor-Driver)\\ | ||
| + | 2x SSD1306 Screens with 64x128 Pixels - 7Pin Variant!!!\\ | ||
| + | 4x Encoders with inbuilt switches\\ | ||
| + | 1x Momentary Button for "Play/Pause"\\ | ||
| + | 1x Breathboard ca. 100x50mm\\ | ||
| + | 3 days time\\ | ||
| + | \\ | ||
| + | There are a lot of wires, nuts and screw which i have not listed here, here are only the big and expensive parts:\\ | ||
| + | \\ | ||
| + | **Amazon/Ebay/Ali...**\\ | ||
| + | Turner Motor:[[https://www.amazon.de/dp/B07YQQGQ4C?psc=1&ref=ppx_yo2ov_dt_b_product_details| | ||
| + | Iverntech NEMA 17 Schrittmotor mit integrierter 400 mm T8-Leitspindel]] I dont think that is a good choice, the T8 Spindle bends to much... better you M10-M12 ones and 450mm or more Travel\\ | ||
| + | // | ||
| + | Feeder Motor: [[https://www.amazon.de/dp/B07JYGRFFL?psc=1&ref=ppx_yo2ov_dt_b_product_details|Akozon Linearschiene]] - this hasent come in good condition, the first 5cm moove a bit woobly\\ | ||
| + | // | ||
| + | Corner-Mounts: [[https://www.amazon.de/dp/B07RG9XCM2?psc=1&ref=ppx_yo2ov_dt_b_product_details|Justech 10x Winkelverbinder Aluprofil 20x20mm]] better order 2 sets...\\ | ||
| + | // | ||
| + | 20x20mm Profiles: [[https://www.amazon.de/dp/B0BGKJYQ9Z?ref=ppx_yo2ov_dt_b_product_details&th=1|CNCYEAH 4 Stück 800mm Aluminiumprofil20X20 T]]\\ | ||
| + | // | ||
| + | Stepper Motor Driver: [[https://www.amazon.de/dp/B07YWZRXGR?psc=1&ref=ppx_yo2ov_dt_b_product_details|DM542 Schrittmotor Controller]] you need 2 off them!\\ | ||
| + | \\ | ||
| + | PSU: [[https://www.amazon.de/dp/B0BVJ2RZ9B?psc=1&ref=ppx_yo2ov_dt_b_product_details|Schaltnetzteil 24V 10A ]]\\ | ||
| + | \\ | ||
| + | Mounting Kit for the Turner-Motor: [[https://www.amazon.de/dp/B07F8RLPBC?psc=1&ref=ppx_yo2ov_dt_b_product_details|42 mm Schrittmotor-Halterung]] not the stabelst one... mooves under Load...find better...\\ | ||
| + | \\ | ||
| + | Microswitches: [[https://www.amazon.de/dp/B07F9QKTQQ?psc=1&ref=ppx_yo2ov_dt_b_product_details|Mikroschalter Endschalter mit Rollenhebel 250V 5A SPDT 1NO 1NC]] you need 2 off them\\ | ||
| + | \\ | ||
| + | V-Rolls for Wires: [[https://www.amazon.de/dp/B07LF9L16L?psc=1&ref=ppx_yo2ov_dt_b_product_details|V624ZZ Kugellager V Nut Rillenkugellager]] you will need 6 off them and special M4 Screws else they will not moove\\ | ||
| + | \\ | ||
| + | T8 Nuts: [[https://www.amazon.de/dp/B086QJCX1M?psc=1&ref=ppx_yo2ov_dt_b_product_details|T8 Mutter Gewindespindel Messing Mutter]] you need 3 off them, but you may find a better way to mount your pipe on the Spindle!\\ | ||
| + | \\ | ||
| + | Flange Bearing: [[https://www.amazon.de/dp/B01MZ2M2GC?psc=1&ref=ppx_yo2ov_dt_b_product_details|Flanschlager]] you need 2 off it...\\ | ||
| + | |||
| + | ===== Menue Structure ===== | ||
| + | Menue 1: Load and Save Coil-Data\\ | ||
| + | {{phatline:Coil-Winder-Menu1.jpg?600|}}\\ | ||
| + | // | ||
| + | Menue 2: Edit Coil-Data, and get some resulting values\\ | ||
| + | {{phatline:Coil-Winder-Menu2.jpg?600|}}\\ | ||
| + | |||
| + | // | ||
| + | Menue 3: Start the Operation, guide thru Stages\\ | ||
| + | {{phatline:Coil-Winder-Menu3-stage-1.jpg?600|}}\\ | ||
| + | {{phatline:Coil-Winder-Menu3-stage-2.jpg?600|}}\\ | ||
| + | {{phatline:Coil-Winder-Menu3-stage-3.jpg?600|}}\\ | ||
| + | {{phatline:Coil-Winder-Menu3-stage-4.jpg?600|}}\\ | ||
| + | {{phatline:Coil-Winder-Menu3-stage-5.jpg?600|}}\\ | ||
| + | {{phatline:Coil-Winder-Menu3-stage-6.jpg?600|}}\\ | ||
| ===== Community users working on it ===== | ===== Community users working on it ===== | ||
coilwinder.1680466200.txt.gz · Last modified: 2023/04/02 20:10 by phatline
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
