control_board
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
control_board [2022/01/06 02:19] phatline |
control_board [2022/01/08 15:13] (current) phatline |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Control Panel for AIN_4 v1.2 ====== | + | ====== Control Panel AIN_4 & AOUT_4 v1.2 ====== |
| + | ===== AIN4 - AOUT4 v1.2 TOP ===== | ||
| + | {{:phatline:Control-Top.jpg?800|}}\\ | ||
| + | **BOM:**\\ | ||
| + | [[https://www.taydaelectronics.com/electromechanical/switches-key-pad/push-button-switch-dc-30v-0-1a-dpdt-7x7mm.html|8x Switch better take mouser ones...]]\\ | ||
| + | LED5-8: Normal LEDs\\ | ||
| + | LED1-4: Bipolar LED comman Anode\\ | ||
| + | VR1-4 AOUT4: 10K Lin\\ | ||
| + | VR1-4 AIN4: 100K Lin\\ | ||
| + | SKT1-4: 3,5 mono Jack\\ | ||
| + | JP21: Optional Clock Input from SKT5 (then don't set G1_G5 on the backside) \\ | ||
| + | J1: Routes gate outputs from a standard DOUT pinheader to SKT 5-8 according to solder jumper pairs Gxx\\ | ||
| + | ===== AIN_4 v1.2 BACK ===== | ||
| + | {{:phatline:Control-AOUT-back.jpg?800|}}\\ | ||
| + | **BOM:**\\ | ||
| + | RN1: 100k iso 652-4816P-1LF-100K\\ | ||
| + | SJ 1-4: let them unsoldered\\ | ||
| + | SJ 5-8: solder a 1K 0603 SMD Resistor from the Round PAD to GROUND- to avoid Floating\\ | ||
| + | Diodes: 1N4148 > only Stuff in AOUT4 Usecases\\ | ||
| + | IC2: 74LV14H (SOIC14)\\ | ||
| + | C2: 100nF Kerko\\ | ||
| + | The Rest: cant remember...Resistors and Caps...\\ | ||
| + | \\ | ||
| + | about G5_G1, G2_G6, G4_G8, G7_G3:\\ | ||
| + | J1 you connect to a DOUTx4 output, which deliver 8 DOUTs on 1 shroudet header\\ | ||
| + | But we only use 4 DOUTs on the Controlboards... with this jumpers you decide which one!\\ | ||
| + | IF you use a CLOCK coming from J21, then dont set G1_G5!\\ | ||
| ===== Front-Panel for AIN_4 v1.2 ===== | ===== Front-Panel for AIN_4 v1.2 ===== | ||
| i measeured the PCB, and made a drawing in order to create a hand-drilled Frontpanel... | i measeured the PCB, and made a drawing in order to create a hand-drilled Frontpanel... | ||
| - | so dont take the values as 100% true...: | + | so dont take the values as 100% true...:\\ |
| - | {{ :phatline:Control-Panel.jpg?800|}} | + | {{:phatline:Control-Panel.jpg?800|}} |
| + | |||
| + | {{ :phatline:Control-AOUT-seite.jpg?255|}} | ||
| + | {{ :phatline:Control-AIN-AOUT-Panel-Label.jpg?500|}} | ||
| - | {{ :phatline:Control-AOUT-seite.jpg?400|}} | + | **LABELS:**\\ |
| - | {{ :phatline:Control-AIN-AOUT-Panel-Label.jpg?600|}} | + | linke Schalter: offset (uni/bipolar)\\ |
| + | rechte Schalter: range (+5V/+10V insgesamt)\\ | ||
| + | \\ | ||
| + | **Deswegen folgende Möglichkeiten für Ein- bzw. Ausgänge:**\\ | ||
| + | 0 bis +2,5V\\ | ||
| + | 0 bis +5V\\ | ||
| + | -2,5 bis +2,5V\\ | ||
| + | -5 bis +5V \\ | ||
control_board.1641435580.txt.gz · Last modified: 2022/01/06 02:19 by phatline
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
