This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
control_board [2022/01/06 02:48] phatline [AIN4 - AOUT4 v1.2 TOP] |
control_board [2022/01/08 15:13] (current) phatline |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Control Panel for AIN_4 & AOUT_4 v1.2 ====== | + | ====== Control Panel AIN_4 & AOUT_4 v1.2 ====== |
===== AIN4 - AOUT4 v1.2 TOP ===== | ===== AIN4 - AOUT4 v1.2 TOP ===== | ||
{{:phatline:Control-Top.jpg?800|}}\\ | {{:phatline:Control-Top.jpg?800|}}\\ | ||
Line 8: | Line 8: | ||
VR1-4 AOUT4: 10K Lin\\ | VR1-4 AOUT4: 10K Lin\\ | ||
VR1-4 AIN4: 100K Lin\\ | VR1-4 AIN4: 100K Lin\\ | ||
- | SKT1-4: 3,5 Stereo Jack?\\ | + | SKT1-4: 3,5 mono Jack\\ |
- | JP21: Clock Input(if you have, then dont set G1_G5 on the backside) \\ | + | JP21: Optional Clock Input from SKT5 (then don't set G1_G5 on the backside) \\ |
- | J1: Gate/DOUT/Clock - Input - pinout see DOUTx4-Board\\ | + | J1: Routes gate outputs from a standard DOUT pinheader to SKT 5-8 according to solder jumper pairs Gxx\\ |
===== AIN_4 v1.2 BACK ===== | ===== AIN_4 v1.2 BACK ===== | ||
{{:phatline:Control-AOUT-back.jpg?800|}}\\ | {{:phatline:Control-AOUT-back.jpg?800|}}\\ | ||
Line 16: | Line 16: | ||
RN1: 100k iso 652-4816P-1LF-100K\\ | RN1: 100k iso 652-4816P-1LF-100K\\ | ||
SJ 1-4: let them unsoldered\\ | SJ 1-4: let them unsoldered\\ | ||
- | SJ 5-8: solder a 1K 0603 SMD Resistor from the Round PAD to 5V- to avoid Floating\\ | + | SJ 5-8: solder a 1K 0603 SMD Resistor from the Round PAD to GROUND- to avoid Floating\\ |
Diodes: 1N4148 > only Stuff in AOUT4 Usecases\\ | Diodes: 1N4148 > only Stuff in AOUT4 Usecases\\ | ||
IC2: 74LV14H (SOIC14)\\ | IC2: 74LV14H (SOIC14)\\ | ||
C2: 100nF Kerko\\ | C2: 100nF Kerko\\ | ||
The Rest: cant remember...Resistors and Caps...\\ | The Rest: cant remember...Resistors and Caps...\\ | ||
+ | \\ | ||
+ | about G5_G1, G2_G6, G4_G8, G7_G3:\\ | ||
+ | J1 you connect to a DOUTx4 output, which deliver 8 DOUTs on 1 shroudet header\\ | ||
+ | But we only use 4 DOUTs on the Controlboards... with this jumpers you decide which one!\\ | ||
+ | IF you use a CLOCK coming from J21, then dont set G1_G5!\\ | ||
===== Front-Panel for AIN_4 v1.2 ===== | ===== Front-Panel for AIN_4 v1.2 ===== | ||
i measeured the PCB, and made a drawing in order to create a hand-drilled Frontpanel... | i measeured the PCB, and made a drawing in order to create a hand-drilled Frontpanel... | ||
Line 29: | Line 33: | ||
{{ :phatline:Control-AOUT-seite.jpg?255|}} | {{ :phatline:Control-AOUT-seite.jpg?255|}} | ||
{{ :phatline:Control-AIN-AOUT-Panel-Label.jpg?500|}} | {{ :phatline:Control-AIN-AOUT-Panel-Label.jpg?500|}} | ||
+ | |||
+ | **LABELS:**\\ | ||
+ | linke Schalter: offset (uni/bipolar)\\ | ||
+ | rechte Schalter: range (+5V/+10V insgesamt)\\ | ||
+ | \\ | ||
+ | **Deswegen folgende Möglichkeiten für Ein- bzw. Ausgänge:**\\ | ||
+ | 0 bis +2,5V\\ | ||
+ | 0 bis +5V\\ | ||
+ | -2,5 bis +2,5V\\ | ||
+ | -5 bis +5V \\ |