enc_4_4
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
enc_4_4 [2018/03/05 23:52] – latigid_on | enc_4_4 [2018/03/06 18:45] – [Dimensions] latigid_on | ||
---|---|---|---|
Line 13: | Line 13: | ||
===== BOM v1.0 ===== | ===== BOM v1.0 ===== | ||
- | ^Part ^Value ^ | + | ^ Type ^ Part ^ Value ^ |
- | | C25 | DNF | | + | |Caps | C25 | DNF | |
- | | C26 | DNF | | + | | | C26 | DNF | |
- | | C29 | 10uF polarised | | + | | | C29 | 10uF polarised | |
- | | EN1 | 12mm | + | |Encoder | EN1 | 12mm | |
- | | EN2 | 12mm | | + | | | EN2 | 12mm | |
- | | J1 | PINHD-2X54WALL | | + | |Header |
- | | J2 | +5V | | + | | | J2 | +5V | |
- | | J5 | PINHD-2X54WALL | | + | | | J5 | PINHD-2X54WALL | |
- | | LCD1 | 0.96_OLED | | + | |OLEDs |
- | | LCD2 | 0.96_OLED | | + | | | LCD2 | 0.96_OLED | |
- | | LCD3 | 0.96_OLED | | + | | | LCD3 | 0.96_OLED | |
- | | LCD4 | 0.96_OLED | | + | | | LCD4 | 0.96_OLED | |
- | | R3 | DNF | | + | |Resistors | R3 | DNF | |
- | | R4 | DNF | | + | | | R4 | DNF | |
- | | R7 | DNF | | + | | | R7 | DNF | |
- | | R9 | 2k2 | | + | | | R9 | 2k2 | |
- | | S1(A) | DT6 or 6mm | | + | |Switches | S1(A) | DT6 or 6mm | |
- | | S2(A) | DT6 or 6mm | | + | | | S2(A) | DT6 or 6mm | |
- | | S3(A) | DT6 or 6mm | | + | | | S3(A) | DT6 or 6mm | |
- | | S4(A) | DT6 or 6mm | | + | | | S4(A) | DT6 or 6mm | |
- | | S5(A) | DT6 or 6mm | | + | | | S5(A) | DT6 or 6mm | |
- | | S6(A) | DT6 or 6mm | | + | | | S6(A) | DT6 or 6mm | |
Line 46: | Line 47: | ||
===== Assembly ===== | ===== Assembly ===== | ||
+ | Decide on the configuration to be used. Any combination of switches, encoders or OLEDs is possible if they fit. | ||
+ | Only one encoder is wired to the J1 header. If you want to use the EN2 position, wire the legs to the empty EN1 solder points. | ||
+ | |||
+ | R9 and C29 form the power-on reset for OLEDs. R7 should not be installed. R3/ | ||
+ | |||
+ | The switches accommodate either DT6 or 6mm switches (obviously only one type!). For DT6 switches, ensure the flat side is aligned with the PCB silkscreen. | ||
+ | |||
+ | J2 can supply power if needed. | ||
Line 52: | Line 61: | ||
==== Interconnections ==== | ==== Interconnections ==== | ||
- | * J1 | + | {{:: |
+ | J1 is the SCS header, connecting to J10A | ||
- | ===== Dimensions ===== | + | J2 can provide power as indicated; it is also connected on J5. |
- | {{: | + | J5 connects to J15 on the Core (or equivalent) |
+ | |||
+ | ===== Dimensions ===== | ||
- | {{ :encs:encs_dxf.zip }} | + | {{:scsoled:scsoled.png? |
+ | {{ : | ||
===== License ===== | ===== License ===== | ||
enc_4_4.txt · Last modified: 2018/03/06 21:10 by latigid_on