euro-midi-io
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
euro-midi-io [2022/02/06 06:31] phatline [EuroRack - Midi IO - Board] |
euro-midi-io [2022/02/11 15:21] phatline [PCB] |
||
|---|---|---|---|
| Line 10: | Line 10: | ||
| {{:phatline:EURO_Midi_IO_Shematic.jpg?900|}}\\ | {{:phatline:EURO_Midi_IO_Shematic.jpg?900|}}\\ | ||
| + | |||
| + | FIXME - The Connection from J1 to J2 is wrong - its 1:1 but it has to be crossed.\\ | ||
| ====== Hardware Requirements ====== | ====== Hardware Requirements ====== | ||
| * Soldering Iron - with a Dip that can Handle Thruhole-Parts and 1206 SMDs, solder Paste...\\ | * Soldering Iron - with a Dip that can Handle Thruhole-Parts and 1206 SMDs, solder Paste...\\ | ||
| Line 76: | Line 78: | ||
| ---never the less i did not testet Rev.B... since i have enough Rev.A for my whole Modular-Rack @ home\\ | ---never the less i did not testet Rev.B... since i have enough Rev.A for my whole Modular-Rack @ home\\ | ||
| so feel free to test - and report!\\ | so feel free to test - and report!\\ | ||
| + | {{:phatline:EURO_Midi_IO_Board.jpg?900|}}\\ | ||
| + | FIXME - dont use this - because of J1-J2 connection is wrong (this matter if you chain 2 Midi-IO-Modules\\ | ||
| ====== Frontpanel====== | ====== Frontpanel====== | ||
| {{:phatline:Euro_Midi_IO_Panel-Dimensions.jpg?900|}}\\ | {{:phatline:Euro_Midi_IO_Panel-Dimensions.jpg?900|}}\\ | ||
| - | **I made a DXF File which you can print, and drill it DIY or \\ | + | **I made a {{:phatline:EuroMidiIO-Panel-for-milling.zip?900|DXF}}File which you can print, and drill it DIY or \\ |
| - | you can send to:** (once the prototypestate is gone)\\ | + | you can send to:**\\ |
| - | [[https://shop.frontpanels.de/custom-panels|frontpanels.de in germany]] 17,08€ a panel (5x-10%, 10x-20%, 20x-30%, 30x-40%, 100x-50%\\ | + | [[https://shop.frontpanels.de/custom-panels|frontpanels.de in germany]] 17,08€ a panel (5x-10%, 10x-20%, 20x-30%, 30x-40%, 100x-50%)\\ |
| - | [[https://thebeast.co.uk/2d/|The Beast - UK]]\\ | + | I tested one with them - and yes they looking good - and they fit!:\\ |
| - | [[https://www.schaeffer-ag.de/en/|Schaeffer-ag.de]] | + | \\ |
| + | another good guy: [[https://thebeast.co.uk/2d/|The Beast - UK]]\\ | ||
| \\ | \\ | ||
| **Recommend Material**\\ | **Recommend Material**\\ | ||
| 2mm x 128.5 x 17.78 Aluminium, anodised\\ | 2mm x 128.5 x 17.78 Aluminium, anodised\\ | ||
| - | {{:phatline:Frontpanel-EuroMidi.zip?900|}} - NOT TESTET\\ | ||
| \\ | \\ | ||
| **A cheaper way is: order a 1,6mm thick Aluminium PCB as Frontpanel:**\\ | **A cheaper way is: order a 1,6mm thick Aluminium PCB as Frontpanel:**\\ | ||
| - | I will test this... this are the gerbers:\\ | + | this are the gerbers:\\ |
| + | {{:phatline:GERBER-EURO_MidiIO_FP.zip?900|}}\\ | ||
| + | I have testet it, and this 1.6mm Aluminium from JLCPCB is too thin, i endet up by sandwith 2 off them togehter - so its strong enough, since the Labels are reversed when use the PCB reversed - i now removed them in this gerber file!\\ | ||
| {{:phatline:Euro_Midi_IO_3D_RENDER-Panel.jpg?900|}}\\ | {{:phatline:Euro_Midi_IO_3D_RENDER-Panel.jpg?900|}}\\ | ||
| + | |||
euro-midi-io.txt · Last modified: 2022/02/11 15:23 by phatline
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
