fantomxr
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
fantomxr [2015/01/21 12:28] fantomxr |
fantomxr [2015/01/21 12:37] (current) fantomxr |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| On this page I will list pcb designs I made. Some are tested, some are not. I will add a note to every PCB. | On this page I will list pcb designs I made. Some are tested, some are not. I will add a note to every PCB. | ||
| + | Most of them are not that special. But they make the midibox-life easier. | ||
| \\ | \\ | ||
| \\ | \\ | ||
| Line 54: | Line 55: | ||
| {{:fantomxr_8xswitch.png?500|}} | {{:fantomxr_8xswitch.png?500|}} | ||
| + | \\ | ||
| + | \\ | ||
| ==== Fatar keybed adapter ==== | ==== Fatar keybed adapter ==== | ||
| Line 70: | Line 73: | ||
| Status: **untested**\\ | Status: **untested**\\ | ||
| - | Eagle *.brd: [[https://www.dropbox.com/s/y5kh9n5zghuzk0v/DIO-Adapter 8 auf 2x6pin.brd?dl=0|Download]] | + | Eagle *.brd: [[https://www.dropbox.com/s/evby49o42hru6yt/DIO-Adapter%208%20auf%202x6pin.brd?dl=0|Download]] |
| {{:fantomxr_dio_6pin.png?500|}} | {{:fantomxr_dio_6pin.png?500|}} | ||
| Line 77: | Line 80: | ||
| \\ | \\ | ||
| + | ==== DIO Adapter 1x10pin ==== | ||
| + | Same as above but for 10pin. Can also be chained. | ||
| + | Status: **untested**\\ | ||
| + | Eagle *.brd: [[https://www.dropbox.com/s/7flat7vsjr9vqbb/DIO-Adapter%208%20auf%201x10pin.brd?dl=0|Download]] | ||
| + | |||
| + | {{:fantomxr_dio_10pin.png?500|}} | ||
| + | |||
| + | \\ | ||
| + | \\ | ||
| + | |||
| + | ==== 10pin splitter ==== | ||
| + | This is an adapter for split an 10pin pinheader into 2x 6pin. This is useful, if you want to connect two of my 4x switchboards directly to a DIN module. | ||
| + | |||
| + | Status: **untested**\\ | ||
| + | Eagle *.brd: [[https://www.dropbox.com/s/ru4wxj5p2mrh3mv/10%20auf%202x3.brd?dl=0|Download]] | ||
| + | |||
| + | {{:fantomxr_10pin_split.png?200|}} | ||
| + | |||
| + | \\ | ||
| + | \\ | ||
| + | |||
| + | ==== USB I/O ==== | ||
| + | Because the Neutrik USB jack which comes in a D-housing is quite expensive, I set up this little board. | ||
| + | |||
| + | Status: **tested**\\ | ||
| + | Eagle *.brd: [[https://www.dropbox.com/s/8d4t99wnr1p62hb/USB-Platine.brd?dl=0|Download]] | ||
| + | |||
| + | {{:fantomxr_usb_platine.png?200|}} | ||
| + | |||
| + | \\ | ||
| + | \\ | ||
fantomxr.1421843292.txt.gz ยท Last modified: 2015/01/21 12:28 by fantomxr
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
