home:mbhp:module:din
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
home:mbhp:module:din [2008/12/02 20:15] Just Phil |
home:mbhp:module:din [2008/12/20 01:45] (current) stryd_one Fixed link |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| ===== Getting Started ===== | ===== Getting Started ===== | ||
| - | * [[:home:skills:preparation | Preparation]] | + | * [[:home:skills:tools| Tools]] |
| * [[:home:skills:soldering]] | * [[:home:skills:soldering]] | ||
| Line 17: | Line 17: | ||
| * etc | * etc | ||
| ===== Details ===== | ===== Details ===== | ||
| + | |||
| === Pins === | === Pins === | ||
| [[din_dout_pin_list | DIN & DOUT pin table]] | [[din_dout_pin_list | DIN & DOUT pin table]] | ||
| + | |||
| + | |||
| + | |||
| + | ===Available Ports=== | ||
| + | |||
| + | Following interfaces are provided by the dinx4 module: | ||
| + | |||
| + | | Name ^No. of pins ^Description | | ||
| + | ^J1 |5 |Interface to CORE J9 (if buttons are used) and CORE J6 (if encoders are used, MIDIbox16E only). DINX4 J1 provides two power pins for 5V, 0V, the serial clock, the latch enable and the serial output of the register chain. This port can also be connected with J2 of another DINX module.| | ||
| + | ^J2 |5 |Interface to another DINX4 module. DINX4:J2 provides nearly the same pins like J1, just only the serial output of the first IC is replaced by the serial input of the last IC. This port can be connected with J1 of another DINX module.| | ||
| + | ^J3 to J9 |5 |These are the digital input lines, every connector comes with 4 of them and an additional pin for ground. See mbhp_dinx4_32buttons.pdf as an example how to connect buttons to these pins, and mbhp_dinx4_16enc.pdf how to connect rotary | | ||
| === PCB files === | === PCB files === | ||
| Line 53: | Line 65: | ||
| ==== Building instructions ==== | ==== Building instructions ==== | ||
| blah blah blah | blah blah blah | ||
| - | |||
| ==== Connection to Core Module ==== | ==== Connection to Core Module ==== | ||
| Line 62: | Line 73: | ||
| \\ | \\ | ||
| + | |||
| + | ==== Connecting Input Devices ==== | ||
| + | [[http://www.ucapps.de/mbhp/mbhp_dinx4_32buttons.pdf|Connecting 32 buttons to a DINX4]] | ||
| + | [[http://www.ucapps.de/mbhp/mbhp_dinx4_16enc.pdf|Connecting 16 Rotary Ecnoders to the MIDIbox16E and other MIOS based controllers]] | ||
| + | [[http://www.ucapps.de/mbhp/mbhp_dinx4_16enc_alps_stec16b03.pdf|Connecting 16 Alps STEC16B03 Encoders to MIDIbox16E and other MIOS based controllers]] | ||
| + | [[http://www.ucapps.de/mbhp/mbhp_din_touchsensors.pdf|Connection Diagram for touch Sensors]] | ||
| ==== Testing ==== | ==== Testing ==== | ||
home/mbhp/module/din.1228248910.txt.gz ยท Last modified: 2008/12/02 20:15 by Just Phil
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
