lre-oled-bar
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
lre-oled-bar [2022/01/13 03:11] phatline [BOM LCSC] |
lre-oled-bar [2022/02/04 14:22] phatline [To Do] |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| {{:phatline:LRE-OLED-BAR-3D-Perspektive.jpg?600|}}\\ | {{:phatline:LRE-OLED-BAR-3D-Perspektive.jpg?600|}}\\ | ||
| {{:phatline:Frontpanel-massen.jpg?900|}}\\ | {{:phatline:Frontpanel-massen.jpg?900|}}\\ | ||
| + | |||
| + | **I made this PCBs to use it with Fairlightii´s [[mb-lre8x2cs_pcb]]**\\ | ||
| **4x PCBs on one 100x100mm**\\ | **4x PCBs on one 100x100mm**\\ | ||
| Line 9: | Line 11: | ||
| With this Method you pay for 20 PCBs 8€ all inclusive to EU-Austria\\ | With this Method you pay for 20 PCBs 8€ all inclusive to EU-Austria\\ | ||
| So you can Stuff 5 LRE8x2 with this.\\ | So you can Stuff 5 LRE8x2 with this.\\ | ||
| + | Here are the gerberfiles for production - i made it with[[https://jlcpcb.com/|JLCPCB]]\\ | ||
| + | {{:phatline:LRE-OLED-RevA-Gerber.zip?900|}}\\ | ||
| + | {{:phatline:JLCPCB-low-cost.jpg?476|}}\\ | ||
| + | And they are working, they also V-Grooved on my marking without extra costs...\\ | ||
| + | My next Revision would be a Micromatch header on the left side of the pcbs so i can directly interconnect to a Display Driver (crimping instead of soldering)\\ | ||
| ====== Hardware Requirements ====== | ====== Hardware Requirements ====== | ||
| * a MIOS32 Core to connect too\\ | * a MIOS32 Core to connect too\\ | ||
| Line 16: | Line 23: | ||
| ====== Shematic ====== | ====== Shematic ====== | ||
| {{:phatline:LRE-OLED-BAR-Shematic.jpg?400|}}\\ | {{:phatline:LRE-OLED-BAR-Shematic.jpg?400|}}\\ | ||
| - | Full Shematic:\\ | + | **Full**: {{:phatline:LRE-OLED-BAR-Shematic.pdf?800|}}\\ |
| - | {{:phatline:LRE-OLED-BAR-Shematic.pdf?800|}}\\ | + | |
| - | ====== Building ====== | + | ====== Building and BOM====== |
| - | There are 1Row 7Pin headers (2.54mm pitch) on the Backside of the PCB\\ | + | The Values are printet on the PCB. |
| - | The Values are printet on the PCB. Following Quantity is for 4 PCBs:\\ | + | |
| + | **Following Quantity is for 4 PCBs:**\\ | ||
| + | 8x 1Row 7Pin headers (2.54mm pitch)\\ | ||
| 8x 1K 1208 SMD Resistors\\ | 8x 1K 1208 SMD Resistors\\ | ||
| 12x 10uF 1208 Capacitors (non polarized)\\ | 12x 10uF 1208 Capacitors (non polarized)\\ | ||
| - | 8x 0.96" SSD1306 Screens\\ | ||
| 3x 10K 0603 SMD Resistors which are optional\\ | 3x 10K 0603 SMD Resistors which are optional\\ | ||
| {{:phatline:LRE-OLED-BAR-3D-Back.jpg?700|}}\\ | {{:phatline:LRE-OLED-BAR-3D-Back.jpg?700|}}\\ | ||
| - | On the Frontside you put in the Screens | + | 8x 0.96" SSD1306 Screens\\ |
| {{:phatline:LRE-OLED-BAR-3D-Front.jpg?700|}}\\ | {{:phatline:LRE-OLED-BAR-3D-Front.jpg?700|}}\\ | ||
| - | ===== BOM LCSC===== | + | ====== Frontpanel====== |
| - | these are the parts which must be handsoldered\\ | + | {{:phatline:Frontpanel.jpg?700|}}\\ |
| - | ^Comment^Designator^Footprint^LCSC Part Number^Lot^ | + | I made a DXF File which you can send to [[https://www.formulor.de/|Formulor in Germany]]\\ |
| - | |ULN2003ADRW|Q1-Q3|SOIC-18_300mil|C9683|3| | + | |
| - | |PEC11R-4015F-S24|ENC1-ENC5|tht|C143789|5| | + | |
| - | |Micromatch-2x5|LCDi1,LCDo1,Ji89,Jo89|tht|C590954|4| | + | |
| - | |Switch|S1|tht|C273513|1| | + | |
| - | **S1 can be stuffed with:** Matias, CherryMX, MEC-3FTH9, TL1265\\ | + | |
| + | i panalized it so there are 2 Plates in it\\ | ||
| + | I payed 40€ summed for booth plates incl shipping from Germany to Austria\\ | ||
| - | ===== BOM AliExpress===== | + | The Version with the not needet 3mm Mounting holes for the LRE8x2:{{:phatline:2xLRE-OLED-BAR-DXF.zip?700|}}\\ |
| - | [[https://de.aliexpress.com/item/32831561142.html?spm=a2g0s.9042311.0.0.27424c4dzZbi5A|2xSSD1306-7Pin]] | + | |
| + | My Orginal Autocad Drawing, + DXFs for Fabrication without the non needet Mounting Holes:{{:phatline:EURO-LRE-Frontpanel.zip?700|}}\\ | ||
| + | **Recommend Material from Formulor:**\\ | ||
| + | 3mm Acrylglas GS 384x384mm, mittelgrau transparent(7C83)\\ | ||
| - | |||
| - | ===== PART Locations===== | ||
| - | {{:phatline:LRE5-LCD2-PCP-Parts.png?500|}}\\ | ||
| ====== To Do ====== | ====== To Do ====== | ||
| - | making Revision 2, because in 1 the Transistor-Array-Fottprint is wrong and had to bridged\\ | + | The LRE-OLED-Bar & The Frontpanel are only a Port of my [[MSQ-CC-LRE-V2]]\\ |
| - | {{:phatline:LRE5-LCD2-Proto-Bridges.jpg?500|}}\\ | + | so look there for more information.... |
| ====== Community users working on it ====== | ====== Community users working on it ====== | ||
| * **[[Phatline]]** = PCB & Shematic, UI-Programming, Documentation...\\ | * **[[Phatline]]** = PCB & Shematic, UI-Programming, Documentation...\\ | ||
| Just let a Private message on the forum to user already involved.\\ | Just let a Private message on the forum to user already involved.\\ | ||
lre-oled-bar.txt · Last modified: 2022/02/04 14:22 by phatline
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
