lre-oled-bar
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
lre-oled-bar [2022/01/13 03:16] phatline |
lre-oled-bar [2022/02/04 14:22] phatline [To Do] |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| {{:phatline:LRE-OLED-BAR-3D-Perspektive.jpg?600|}}\\ | {{:phatline:LRE-OLED-BAR-3D-Perspektive.jpg?600|}}\\ | ||
| {{:phatline:Frontpanel-massen.jpg?900|}}\\ | {{:phatline:Frontpanel-massen.jpg?900|}}\\ | ||
| + | |||
| + | **I made this PCBs to use it with Fairlightii´s [[mb-lre8x2cs_pcb]]**\\ | ||
| **4x PCBs on one 100x100mm**\\ | **4x PCBs on one 100x100mm**\\ | ||
| Line 9: | Line 11: | ||
| With this Method you pay for 20 PCBs 8€ all inclusive to EU-Austria\\ | With this Method you pay for 20 PCBs 8€ all inclusive to EU-Austria\\ | ||
| So you can Stuff 5 LRE8x2 with this.\\ | So you can Stuff 5 LRE8x2 with this.\\ | ||
| - | Here are the gerberfiles for production - testet on JLCPCB\\ | + | Here are the gerberfiles for production - i made it with[[https://jlcpcb.com/|JLCPCB]]\\ |
| {{:phatline:LRE-OLED-RevA-Gerber.zip?900|}}\\ | {{:phatline:LRE-OLED-RevA-Gerber.zip?900|}}\\ | ||
| + | {{:phatline:JLCPCB-low-cost.jpg?476|}}\\ | ||
| + | And they are working, they also V-Grooved on my marking without extra costs...\\ | ||
| + | My next Revision would be a Micromatch header on the left side of the pcbs so i can directly interconnect to a Display Driver (crimping instead of soldering)\\ | ||
| ====== Hardware Requirements ====== | ====== Hardware Requirements ====== | ||
| * a MIOS32 Core to connect too\\ | * a MIOS32 Core to connect too\\ | ||
| Line 19: | Line 23: | ||
| ====== Shematic ====== | ====== Shematic ====== | ||
| {{:phatline:LRE-OLED-BAR-Shematic.jpg?400|}}\\ | {{:phatline:LRE-OLED-BAR-Shematic.jpg?400|}}\\ | ||
| - | Full Shematic:\\ | + | **Full**: {{:phatline:LRE-OLED-BAR-Shematic.pdf?800|}}\\ |
| - | {{:phatline:LRE-OLED-BAR-Shematic.pdf?800|}}\\ | + | |
| ====== Building and BOM====== | ====== Building and BOM====== | ||
| Line 35: | Line 38: | ||
| {{:phatline:LRE-OLED-BAR-3D-Front.jpg?700|}}\\ | {{:phatline:LRE-OLED-BAR-3D-Front.jpg?700|}}\\ | ||
| + | ====== Frontpanel====== | ||
| + | {{:phatline:Frontpanel.jpg?700|}}\\ | ||
| + | I made a DXF File which you can send to [[https://www.formulor.de/|Formulor in Germany]]\\ | ||
| - | ====== To Do ====== | + | i panalized it so there are 2 Plates in it\\ |
| - | nothing- its the first protypte | + | I payed 40€ summed for booth plates incl shipping from Germany to Austria\\ |
| + | The Version with the not needet 3mm Mounting holes for the LRE8x2:{{:phatline:2xLRE-OLED-BAR-DXF.zip?700|}}\\ | ||
| + | |||
| + | My Orginal Autocad Drawing, + DXFs for Fabrication without the non needet Mounting Holes:{{:phatline:EURO-LRE-Frontpanel.zip?700|}}\\ | ||
| + | |||
| + | |||
| + | **Recommend Material from Formulor:**\\ | ||
| + | 3mm Acrylglas GS 384x384mm, mittelgrau transparent(7C83)\\ | ||
| + | |||
| + | |||
| + | ====== To Do ====== | ||
| + | The LRE-OLED-Bar & The Frontpanel are only a Port of my [[MSQ-CC-LRE-V2]]\\ | ||
| + | so look there for more information.... | ||
| ====== Community users working on it ====== | ====== Community users working on it ====== | ||
| * **[[Phatline]]** = PCB & Shematic, UI-Programming, Documentation...\\ | * **[[Phatline]]** = PCB & Shematic, UI-Programming, Documentation...\\ | ||
| Just let a Private message on the forum to user already involved.\\ | Just let a Private message on the forum to user already involved.\\ | ||
lre-oled-bar.txt · Last modified: 2022/02/04 14:22 by phatline
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
