This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
lre-oled-bar [2022/01/13 03:28] phatline [LRE8x2 096 SSD1306-BAR for Eurorack] |
lre-oled-bar [2022/02/04 14:22] phatline [To Do] |
||
---|---|---|---|
Line 2: | Line 2: | ||
{{:phatline:LRE-OLED-BAR-3D-Perspektive.jpg?600|}}\\ | {{:phatline:LRE-OLED-BAR-3D-Perspektive.jpg?600|}}\\ | ||
{{:phatline:Frontpanel-massen.jpg?900|}}\\ | {{:phatline:Frontpanel-massen.jpg?900|}}\\ | ||
+ | |||
+ | **I made this PCBs to use it with Fairlightii´s [[mb-lre8x2cs_pcb]]**\\ | ||
**4x PCBs on one 100x100mm**\\ | **4x PCBs on one 100x100mm**\\ | ||
Line 9: | Line 11: | ||
With this Method you pay for 20 PCBs 8€ all inclusive to EU-Austria\\ | With this Method you pay for 20 PCBs 8€ all inclusive to EU-Austria\\ | ||
So you can Stuff 5 LRE8x2 with this.\\ | So you can Stuff 5 LRE8x2 with this.\\ | ||
- | Here are the gerberfiles for production - testet on JLCPCB\\ | + | Here are the gerberfiles for production - i made it with[[https://jlcpcb.com/|JLCPCB]]\\ |
{{:phatline:LRE-OLED-RevA-Gerber.zip?900|}}\\ | {{:phatline:LRE-OLED-RevA-Gerber.zip?900|}}\\ | ||
{{:phatline:JLCPCB-low-cost.jpg?476|}}\\ | {{:phatline:JLCPCB-low-cost.jpg?476|}}\\ | ||
+ | And they are working, they also V-Grooved on my marking without extra costs...\\ | ||
+ | My next Revision would be a Micromatch header on the left side of the pcbs so i can directly interconnect to a Display Driver (crimping instead of soldering)\\ | ||
====== Hardware Requirements ====== | ====== Hardware Requirements ====== | ||
* a MIOS32 Core to connect too\\ | * a MIOS32 Core to connect too\\ | ||
Line 19: | Line 23: | ||
====== Shematic ====== | ====== Shematic ====== | ||
{{:phatline:LRE-OLED-BAR-Shematic.jpg?400|}}\\ | {{:phatline:LRE-OLED-BAR-Shematic.jpg?400|}}\\ | ||
- | Full Shematic:\\ | + | **Full**: {{:phatline:LRE-OLED-BAR-Shematic.pdf?800|}}\\ |
- | {{:phatline:LRE-OLED-BAR-Shematic.pdf?800|}}\\ | + | |
====== Building and BOM====== | ====== Building and BOM====== | ||
Line 37: | Line 40: | ||
====== Frontpanel====== | ====== Frontpanel====== | ||
{{:phatline:Frontpanel.jpg?700|}}\\ | {{:phatline:Frontpanel.jpg?700|}}\\ | ||
- | I made a DXF File which you can send to Formulor, i panalized it so there are 2 Plates in it\\ | + | I made a DXF File which you can send to [[https://www.formulor.de/|Formulor in Germany]]\\ |
+ | |||
+ | i panalized it so there are 2 Plates in it\\ | ||
I payed 40€ summed for booth plates incl shipping from Germany to Austria\\ | I payed 40€ summed for booth plates incl shipping from Germany to Austria\\ | ||
- | {{:phatline:2xLRE-OLED-BAR-DXF.zip?700|}}\\ | ||
+ | The Version with the not needet 3mm Mounting holes for the LRE8x2:{{:phatline:2xLRE-OLED-BAR-DXF.zip?700|}}\\ | ||
- | ====== To Do ====== | + | My Orginal Autocad Drawing, + DXFs for Fabrication without the non needet Mounting Holes:{{:phatline:EURO-LRE-Frontpanel.zip?700|}}\\ |
- | nothing- its the first protypte | + | |
+ | |||
+ | **Recommend Material from Formulor:**\\ | ||
+ | 3mm Acrylglas GS 384x384mm, mittelgrau transparent(7C83)\\ | ||
+ | |||
+ | |||
+ | ====== To Do ====== | ||
+ | The LRE-OLED-Bar & The Frontpanel are a Part of my [[MSQ-CC-LRE-V2]]\\ | ||
+ | so look there for more information.... | ||
====== Community users working on it ====== | ====== Community users working on it ====== | ||
* **[[Phatline]]** = PCB & Shematic, UI-Programming, Documentation...\\ | * **[[Phatline]]** = PCB & Shematic, UI-Programming, Documentation...\\ | ||
Just let a Private message on the forum to user already involved.\\ | Just let a Private message on the forum to user already involved.\\ |