This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
mf_ng_board_parts_list [2016/06/28 23:42] psykhaze [MotorFader NG] |
mf_ng_board_parts_list [2016/06/29 00:01] psykhaze [Parts List] |
||
---|---|---|---|
Line 3: | Line 3: | ||
{{ ::neonking:mbhp_mf_v3_proto1.jpg?direct&600 |}} | {{ ::neonking:mbhp_mf_v3_proto1.jpg?direct&600 |}} | ||
- | ===== Introduction ===== | + | * [[http://ucapps.de/mbhp_mf_ng.html|Official UcApps Page]] |
- | [[http://ucapps.de/mbhp_mf_ng.html|Official UcApps Page]] | + | ===== Parts List ===== |
- | the Motorfader NG module was designed with following rules : | + | ^ Description ^ Type ^ Quantity ^ Reichelt Ref ^ Mouser Ref ^ |
- | + | | L293D | IC | 4 | L 293 D | | | |
- | * High-quality faders (Alps K faders with "coreless" motors) Handling | + | | 74HC165 | IC | 1 | 74HC 165 | | |
- | * Deliver stable enough ADC conversion results due to the reduced 3.3V voltage range | + | | PIC18F452-I/P | Microcontroller | 1 | PIC 18F452-I/P | | |
- | * Handle touch sensors properly without heavy CPU load (without an additional external device or microcontroller) | + | | 10 MHz | Quartz | 1 | 10,0000-HC49U-S | | |
- | * PIC based projects Compatible for best usability | + | | 6N138 | Optocoupler | 1 | 6N 138 | | |
- | * DIY friendly and not requiring additional gear for something which isn't part of the MBHP yet | + | | 1N4148 | Diode | 1 | 1N 4148 | | |
- | * Easy Testing and troubleshooting | + | | 1N4002 | Diode | 1 | 1N 4002 | | |
- | + | | 7805 | Voltage Regulator| 1 | uA 7805 | | | |
- | ===== Result ===== | + | | LM317 | Voltage Regulator| 1 | LM317-220 | | |
- | + | | 4*47 kOhm | Resistor Network | 2 | SIL 5-4 47K | | | |
- | * Dedicated PIC controller controls the motorfaders directly. | + | | 1 kOhm | Trimpot | 1 | PT 6-L 1,0K | | |
- | * Firmware can be updated via MIDI! | + | | 100 Ohm | Resistor | 1 | 1/4W 100 | | |
- | * Motorfaders are accessed via MIDI - this allows standalone usage, cascading (to chain multiple modules), and the re-use of existing infrastructure such as MIOS, MIOS Studio and MIOS Bootloader | + | | 220 Ohm | Resistor | 3 | 1/4W 220 | | |
- | * Can either be connected to a PC directly, or controlled from a second PIC or STM32 or LPC17 | + | | 240 Ohm | Resistor | 1 | 1/4W 240 | | |
- | * native support of various protocols (e.g. PitchBender, CCs, even Logic Control and Mackie Control Emulation) | + | | 470 Ohm | Resistor | 2 | 1/4W 470 | | |
- | * support for 8 touch sensors | + | | 1 kOhm | Resistor | 2 | 1/4W 1.0k | | |
- | * instead of TC4427 I'm using L293D now - not at least because of the integrated diodes. | + | | 4.7 kOhm | Resistor | 1 | 1/4W 4.7k | | |
- | * due to the direct motor control connections, the PIC is now able to generate PWM with 50 uS steps for improved motor speed control while a motor is moved | + | | 10 kOhm | Resistor | 2 | 1/4W 10k | | |
- | * Dedicated Firmware for this task, Enough memory free to integrate advanced features, such as runtime-calibration and motor position tracing | + | | 10 uF | Capa Elec | 2 | rad 10/35 | | |
+ | | 2200 uF | Capa Elec | 1 | rad 2.200/25 | | | ||
+ | | 100 nF | Capa Ceram | 6 | Z5U-2,5 100n | | | ||
+ | | 33 pF | Capa Ceram | 2 | Kerko 33p | | | ||
+ | | Green Status LED | LED | 1 | LED 3MM ST GN | | | ||
+ | | PIC Socket | IC-Socket | 1 | GS 40 | | | ||
+ | | L293D/74HC595 Socket | IC-Socket | 5 | GS 16 | | | ||
+ | | Optocoupler Socket | IC-Socket | 1 | GS 8 | | | ||
+ | | MIDI sockets | MIDI Socket | 2 | MABP 5S | | | ||
===== Compatible Motorfaders ===== | ===== Compatible Motorfaders ===== | ||
* **ALPS RASON11M9** - [[http://ucapps.de/mbhp/MF_NG_connection_diagram.pdf|Interconnection Diagram]] | * **ALPS RASON11M9** - [[http://ucapps.de/mbhp/MF_NG_connection_diagram.pdf|Interconnection Diagram]] |