mididocs:seq:launchpadblm
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
mididocs:seq:launchpadblm [2014/09/15 01:50] borfo [SETUP] |
mididocs:seq:launchpadblm [2014/09/15 18:05] (current) borfo |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| **[[mididocs:index|MIDIdocs]]** | **[[mididocs:index|MIDIdocs]]** | ||
| ====== Novation Launchpad Button LED Matrix (BLM) ====== | ====== Novation Launchpad Button LED Matrix (BLM) ====== | ||
| + | [[http://midibox.org/forums/topic/19031-mididocs-novation-launchpad-blm-discussion-thread/|Forum Discussion Thread]] - for comments, corrections, or questions about this article | ||
| - | [[http://midibox.org/forums/topic/13137-midibox-seq-v4-release-feedback/?p=166238|Link to Forum Discussion]] | + | Since firmware version 87, the SEQ V4 supports the use of two [[http://global.novationmusic.com/midi-controllers-digital-dj/launchpad|Novation Launchpads]] as a [[http://ucapps.de/midibox_seq_manual_blm.html|BLM control surface.]] Two Launchpads form a 16x8+X BLM, and up to four can be connected to make a full 16x16+X control surface. |
| - | + | ||
| - | Since firmware version 87, the SEQ V4 supports the use of two Novation Launchpads as a [[http://ucapps.de/midibox_seq_manual_blm.html|BLM control surface.]] Two Launchpads form a 16x8+X BLM, and up to four can be connected to make a full 16x16+X control surface. | + | |
| The Launchpad BLM is implemented as a feature of the JUCE-based BLM emulator software. The launchpads don't connect to the SEQ directly. Instead, they connect to a computer running the JUCE BLM emulator - the emulator software acts as a translator, converting the BLM Protocol sysex messages into midi signals to light the LEDs on the Launchpad, and translating button presses on the Launchpad into a format the SEQ can understand. | The Launchpad BLM is implemented as a feature of the JUCE-based BLM emulator software. The launchpads don't connect to the SEQ directly. Instead, they connect to a computer running the JUCE BLM emulator - the emulator software acts as a translator, converting the BLM Protocol sysex messages into midi signals to light the LEDs on the Launchpad, and translating button presses on the Launchpad into a format the SEQ can understand. | ||
| + | |||
| + | This has been tested with the Novation Launchpad Mini. Presumably, the Launchpad S should work as well, since they're essentially the same controller. The original launchpad hasn't been tested. If you have one, try it and post a comment in the forums to let us know if it works. | ||
| Support for button grid controllers other than the launchpad may be possible in the future. | Support for button grid controllers other than the launchpad may be possible in the future. | ||
| Line 33: | Line 34: | ||
| ...and you're done! | ...and you're done! | ||
| + | |||
| + | =====Resources===== | ||
| + | [[http://midibox.org/forums/topic/13137-midibox-seq-v4-release-feedback/?p=166238|Link to forum thread where this feature was introduced]] | ||
| + | |||
| + | |||
mididocs/seq/launchpadblm.1410745806.txt.gz · Last modified: 2014/09/15 01:50 by borfo
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
