MIDIbox

User Tools

Site Tools

Trace:
euro-midi-io

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
euro-midi-io [2022/02/06 06:30] – phatlineeuro-midi-io [2022/02/11 15:23] (current) – [To Do] phatline
Line 10: Line 10:
  
 {{:phatline:EURO_Midi_IO_Shematic.jpg?900|}}\\ {{:phatline:EURO_Midi_IO_Shematic.jpg?900|}}\\
-\\ + 
-{{:phatline:EURO_Midi_IO_Board.jpg?900|}}\\ +FIXME - The Connection from J1 to J2 is wrong - its 1:1 but it has to be crossed.\\
-\\+
 ====== Hardware Requirements ====== ====== Hardware Requirements ======
   * Soldering Iron - with a Dip that can Handle Thruhole-Parts and 1206 SMDs, solder Paste...\\   * Soldering Iron - with a Dip that can Handle Thruhole-Parts and 1206 SMDs, solder Paste...\\
Line 79: Line 78:
 ---never the less i did not testet Rev.B... since i have enough Rev.A for my whole Modular-Rack @ home\\ ---never the less i did not testet Rev.B... since i have enough Rev.A for my whole Modular-Rack @ home\\
 so feel free to test - and report!\\ so feel free to test - and report!\\
 +{{:phatline:EURO_Midi_IO_Board.jpg?900|}}\\
 +FIXME - dont use this - because of J1-J2 connection is wrong (this matter if you chain 2 Midi-IO-Modules\\
  
  
 ====== Frontpanel====== ====== Frontpanel======
 {{:phatline:Euro_Midi_IO_Panel-Dimensions.jpg?900|}}\\ {{:phatline:Euro_Midi_IO_Panel-Dimensions.jpg?900|}}\\
-**I made a DXF File which you can print, and drill it DIY  or  \\ +**I made a {{:phatline:EuroMidiIO-Panel-for-milling.zip?900|DXF}}File which you can print, and drill it DIY  or  \\ 
-you can send to:** (once the prototypestate is gone)\\ +you can send to:**\\ 
-[[https://shop.frontpanels.de/custom-panels|frontpanels.de in germany]] 17,08€ a panel (5x-10%, 10x-20%, 20x-30%, 30x-40%, 100x-50%\\ +[[https://shop.frontpanels.de/custom-panels|frontpanels.de in germany]] 17,08€ a panel (5x-10%, 10x-20%, 20x-30%, 30x-40%, 100x-50%)\\ 
-[[https://thebeast.co.uk/2d/|The Beast - UK]]\\ +I tested one with them - and yes they looking good - and they fit!:\\ 
-[[https://www.schaeffer-ag.de/en/|Schaeffer-ag.de]]+\\ 
 +another good guy: [[https://thebeast.co.uk/2d/|The Beast - UK]]\\ 
 \\ \\
 **Recommend Material**\\ **Recommend Material**\\
 2mm x 128.5 x 17.78 Aluminium, anodised\\ 2mm x 128.5 x 17.78 Aluminium, anodised\\
-{{:phatline:Frontpanel-EuroMidi.zip?900|}} - NOT TESTET\\ 
 \\ \\
 **A cheaper way is: order a 1,6mm thick Aluminium PCB as Frontpanel:**\\ **A cheaper way is: order a 1,6mm thick Aluminium PCB as Frontpanel:**\\
-I will test this... this are the gerbers:\\+this are the gerbers:\\ 
 +{{:phatline:GERBER-EURO_MidiIO_FP.zip?900|}}\\ 
 +I have testet it, and this 1.6mm Aluminium from JLCPCB is too thin, i endet up by sandwith 2 off them togehter - so its strong enough, since the Labels are reversed when use the PCB reversed - i now removed them in this gerber file!\\
 {{:phatline:Euro_Midi_IO_3D_RENDER-Panel.jpg?900|}}\\ {{:phatline:Euro_Midi_IO_3D_RENDER-Panel.jpg?900|}}\\
 +
  
  
 ====== To Do ====== ====== To Do ======
-Since i already debugged Rev.A - and this is the overworked Rev.B - there should not be much to do, except to test the gerber filers... i am happy with Rev.A (have still PCBs so no check of RevB in near future!)\\+Use a other Midi-OUT-Activity Shematic! - its not working for high speed midi! - while Note-ON off is ok, Midiclock can make trouble (the Charge-Discharge Circuit in this Design is not sufficent for this!)\\
  
 ====== Community users working on it ====== ====== Community users working on it ======
euro-midi-io.1644129028.txt.gz · Last modified: 2022/02/06 06:30 by phatline