Differences

This shows you the differences between two versions of the page.

--- lre-oled-bar [2022/01/13 03:28] – [LRE8x2 096 SSD1306-BAR for Eurorack] phatline
+++ lre-oled-bar [2022/02/04 14:22] (current) – [To Do] phatline
@@ Line 2: / Line 2: @@
 {{:phatline:LRE-OLED-BAR-3D-Perspektive.jpg?600|}}\\
 {{:phatline:Frontpanel-massen.jpg?900|}}\\
+**I made this PCBs to use it with Fairlightii´s [[mb-lre8x2cs_pcb]]**\\
 **4x PCBs on one 100x100mm**\\
@@ Line 9: / Line 11: @@
 With this Method you pay for 20 PCBs 8€ all inclusive to EU-Austria\\
 So you can Stuff 5 LRE8x2 with this.\\
-Here are the gerberfiles for production - testet on JLCPCB\\
+Here are the gerberfiles for production - i made it with[[https://jlcpcb.com/|JLCPCB]]\\
 {{:phatline:LRE-OLED-RevA-Gerber.zip?900|}}\\
 {{:phatline:JLCPCB-low-cost.jpg?476|}}\\
+And they are working, they also V-Grooved on my marking without extra costs...\\
+My next Revision would be a Micromatch header on the left side of the pcbs so i can directly interconnect to a Display Driver (crimping instead of soldering)\\
 ====== Hardware Requirements ======
   * a MIOS32 Core to connect too\\
@@ Line 19: / Line 23: @@
 ====== Shematic ======
 {{:phatline:LRE-OLED-BAR-Shematic.jpg?400|}}\\
-Full Shematic:\\
+**Full**: {{:phatline:LRE-OLED-BAR-Shematic.pdf?800|}}\\
-{{:phatline:LRE-OLED-BAR-Shematic.pdf?800|}}\\
 ====== Building and BOM======
@@ Line 37: / Line 40: @@
 ====== Frontpanel======
 {{:phatline:Frontpanel.jpg?700|}}\\
-I made a DXF File which you can send to Formulor, i panalized it so there are 2 Plates in it\\
+I made a DXF File which you can send to [[https://www.formulor.de/|Formulor in Germany]]\\
+i panalized it so there are 2 Plates in it\\
 I payed 40€ summed for booth plates incl shipping from Germany to Austria\\
-{{:phatline:2xLRE-OLED-BAR-DXF.zip?700|}}\\
+The Version with the not needet 3mm Mounting holes for the LRE8x2:{{:phatline:2xLRE-OLED-BAR-DXF.zip?700|}}\\
-====== To Do ======
+My Orginal Autocad Drawing, + DXFs for Fabrication without the non needet Mounting Holes:{{:phatline:EURO-LRE-Frontpanel.zip?700|}}\\
-nothing- its the first protypte
+**Recommend Material from Formulor:**\\
+mm Acrylglas GS 384x384mm, mittelgrau transparent(7C83)\\
+====== To Do ======
+The LRE-OLED-Bar  &  The Frontpanel are a Part of my [[MSQ-CC-LRE-V2]]\\
+so look there for more information....
 ====== Community users working on it ======
   * **[[Phatline]]** =  PCB & Shematic, UI-Programming, Documentation...\\
 Just let a Private message on the forum to user already involved.\\