tm5-dindoutgate
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
tm5-dindoutgate [2022/12/26 14:18] phatline created |
tm5-dindoutgate [2022/12/28 19:57] (current) phatline [BOM] |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| {{:phatline:TM5-DINDOUTGate-3D-Back.jpg?600|}}\\ | {{:phatline:TM5-DINDOUTGate-3D-Back.jpg?600|}}\\ | ||
| - | this is one essential part for my [[triggermatrix5]]\\ | + | \\ |
| - | it gives 24 Digital Inputs, and 32 Digital Outputs, while 16 Outputs are used for UI, the othere 16 are buffered, and are for use as 16 GAte/Triggger output at 5V Level\\ | + | **it gives;**\\ |
| - | i created this board. its fully SMD, and made it pick and place ready - so no soldering required!\\ | + | 24 Digital Inputs\\ |
| + | 32 Digital Outputs\\ | ||
| + | * while 16 Outputs are used for UI\\ | ||
| + | * the other 16 are buffered, and are for use as 16 GAte/Triggger output at 5V Level\\ | ||
| + | \\ | ||
| + | The Board is fully SMD, and made for pick and place - so no soldering required!\\ | ||
| ====== Shematic ====== | ====== Shematic ====== | ||
| - | {{:phatline:TM5-DINDOUTGate-schema.jpg?600|}}\\ | + | {{:phatline:TM5-DINDOUTGate-schema.jpg?900|}}\\ |
| ====== Building and BOM====== | ====== Building and BOM====== | ||
| - | Its build by pick and place robots... so no need to build\\ | + | Its build by pick and place robots... so no need to build, or order any component\\ |
| + | you need this PCB 1x for [[triggermatrix5]]\\ | ||
| ===== BOM ===== | ===== BOM ===== | ||
| + | Follwing list is for reference, and debugging only,** no need to order them!** all the parts are already soldered on the PCB!\\ | ||
| ^qty ^reference ^value ^footprint ^jlc^ | ^qty ^reference ^value ^footprint ^jlc^ | ||
| - | | 18 | C1 – C12, Ca3, Ca4, Ca5, Cb3, Cb4, Cb5, Cb6| 100n | C_0402 | C307331 | | + | | 18 | C1 – C12, Ca3, Ca4, Ca5, Cb3, Cb4, Cb5, Cb6 | 100n | C_0402 | C307331 | |
| - | | 5 | C9, Ca1, Ca2, Cb1, Cb2| 10uF | C0805 | C440198 | | + | | 5 | C9, Ca1, Ca2, Cb1, Cb2 | 10uF | C0805 | C440198 | |
| - | | 5 | DIN1, DIN2, DIN3, Gate1, Gate2, Gates | Pin-Head-10-SMD C124391 | | + | | 5 | DIN1, DIN2, DIN3, Gate1, Gate2 | Gates | Pin-Head-10-SMD | C124391 | |
| - | | 4 | DOUT1, DOUT2, Jin8/1, Jout8/9 DIN/DOUT | Pin-Head-10-SMD C124391 | | + | | 4 | DOUT1, DOUT2, Jin8/1, Jout8/9 | DIN/DOUT | Pin-Head-10-SMD | C124391 | |
| | 4 | IC1, IC2, IC3, IC4 | 74HC595-bigger | HC595-smd | C5947 | | | 4 | IC1, IC2, IC3, IC4 | 74HC595-bigger | HC595-smd | C5947 | | ||
| | 3 | IC5, IC6, IC7 | 74HC165-bigger | HC165-smd | C5613 | | | 3 | IC5, IC6, IC7 | 74HC165-bigger | HC165-smd | C5613 | | ||
| - | | 1 | LED1 | LED LED-0603 | C2286 | | + | | 1 | LED1 | LED | LED-0603 | C2286 | |
| - | | 16 | Q1 – Q16 | MMBT3904-7-F MMBT3904-7-F | C20526 | | + | | 16 | Q1 – Q16 | MMBT3904-7-F | MMBT3904-7-F | C20526 | |
| - | | 16 | R1 – R16 | 220 R_0805 | C25294 | | + | | 16 | R1 – R16 | 220 | R_0805 | C25294 | |
| - | | 42 | R17 – R74 | 10K R_0402 | C25744 | | + | | 42 | R17 – R74 | 10K | R_0402 | C25744 | |
| - | | 16 | R33 – R48 | 10K R_1206 | C17902 | | + | | 16 | R33 – R48 | 10K | R_1206 | C17902 | |
| - | | 2 | R75, R76 | 220 R_0402 | C25091 | | + | | 2 | R75, R76 | 220 | R_0402 | C25091 | |
| - | + | {{:phatline:TM5-DINDOUTGate-PCB.jpg?800|}}\\ | |
| - | {{:phatline:TM5-DINDOUTGate-PCB.jpg?600|}}\\ | + | |
| ====== To Do ====== | ====== To Do ====== | ||
| waiting for the assembled Prototype\\ | waiting for the assembled Prototype\\ | ||
tm5-dindoutgate.1672064315.txt.gz · Last modified: 2022/12/26 14:18 by phatline
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
