User Tools

Site Tools


enc_4_4

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
enc_4_4 [2018/03/06 18:42]
latigid_on [Interconnections]
enc_4_4 [2018/03/06 21:10] (current)
latigid_on old revision restored (2018/03/05 22:31)
Line 1: Line 1:
-====== ​SCS OLED module ======+====== ​ENCs module ======
  
-Combination of 0.96" SSD1306 OLEDs and switches for an [[http://​www.ucapps.de/​midibox_ng_manual_scs.html|SCS]]+Encoders illuminated with WS2812 LEDs
  
 ===== Schematic ===== ===== Schematic =====
  
 +Power input is +5V via a 3-pin 100mil connector (or Molex) and a Schottky diode. The value of electrolytic capacitor C1 is not critical.
  
 +The pLED chain enters via J2:pin 6 and resistor R1. The resistor should be replaced with a wire link for each additional module (i.e. only the first in the chain gets a resistor, the remainder stuffed with wire links). The serial chain then follows a snake pattern to J3, where additional pLED modules may be connected. The LED ID matches the capacitor name. The RC (R2, C18) end termination shouldn'​t be necessary, but can be trialled should problems with signal reflection arise.
 +
 +Encoders are arranged in columns with outputs on J4--7. The top encoder (EN1/5/9/13 uses pins 10/9, the second (EN2/​6/​10/​14) 8/7 etc. Note that the direction of these encoders is opposite to that of ALPS STEC-12. This needs to be accounted for in an MB_NG config file.
  
  
Line 11: Line 15:
  
  
-===== BOM v1.===== +===== BOM v1.=====
- +
-^ Type ^ Part ^ Value ^ +
-|Caps   ​ | C25 | DNF | +
-| | C26 | DNF | +
-| | C29 | 10uF polarised | +
-|Encoder | EN1 | 12mm | +
-| | EN2 | 12mm | +
-|Header ​ | J1 | PINHD-2X54WALL | +
-| | J2 | +5V | +
-| | J5 | PINHD-2X54WALL | +
-|OLEDs ​         | LCD1 | 0.96_OLED | +
-| | LCD2 | 0.96_OLED | +
-| | LCD3 | 0.96_OLED | +
-| | LCD4 | 0.96_OLED | +
-|Resistors | R3 | DNF | +
-| | R4 | DNF | +
-| | R7 | DNF | +
-| | R9 | 2k2 | +
-|Switches | S1(A) | DT6 or 6mm | +
-| | S2(A) | DT6 or 6mm | +
-| | S3(A) | DT6 or 6mm | +
-| | S4(A) | DT6 or 6mm | +
-| | S5(A) | DT6 or 6mm | +
-| | S6(A) | DT6 or 6mm | +
  
 +^Type     ​^Qty ^Value ^Package ^Parts^Notes^
 +^resistors^
 +|         ​|1 ​  ​|220-470R ​  ​|0204/​7|R1|replace with wire link for each additional module|
 +^capacitors^
 +| |16|100n|1206|C2-17|
 +| |1|100-1000u|electrolytic 3,5-6|C1|
 +^diodes^
 +| |1|1N5187|DO41-7.6|D1|
 +| |16|WS2812B|5050|programmable LEDs|
 +^encoders^
 +| |16|clear shaft 12mm encoders| |EN1--16|
 +^headers^
 +| |6| |2*5 (shrouded) THT|J2-5|can use DIL 100mil breakaway header strips|
 +| |1|         |1X03_SMALL|J1| can use Molex 22-23-2031|
 +^misc^
 +| |16| |spacer pieces| |optional |
  
  
Line 43: Line 38:
  
 ===== Versions ===== ===== Versions =====
-v1.0: first release+v1.0: errata: J4--7 have no connection to ground. J1-3 do carry ground, so it isn't a problem if the DIN modules share the same power rail.
  
 ===== Assembly ===== ===== Assembly =====
  
-Decide on the configuration to be usedAny combination of switches, ​encoders ​or OLEDs is possible if they fit.+1206 caps should go down first, followed by LEDs. The LEDs should ​be oriented with the notch aligned with the silkscreen markThe headers (rear side) are best soldered before the encoders. ​
  
-Only one encoder is wired to the J1 header. If you want to use the EN2 positionwire the legs to the empty EN1 solder points. +The encoders should be installed so they can turn freely. If they are tight against ​the LEDs, the shafts will not turn properlyA spacer piece can be placed around the LED to raise it upIt's then best to straighten the two mounting pins (either side of the three contact pinsforming part of the metal body (otherwise there'​s not enough purchase to get the encoder solidly mounted)A 2mm spacer piece would probably be better than the 3mm one I've distributed.
- +
-R9 and C29 form the power-on reset for OLEDs. R7 should ​not be installedR3/​C25/​R4/​C26 form a termination shunt for OLED data lines. They shouldn'​t ​be required. +
- +
-The switches accommodate either DT6 or 6mm switches ​(obviously only one type!). For DT6 switches, ensure ​the flat side is aligned with the PCB silkscreen. +
- +
-J2 can supply power if needed.+
  
  
Line 61: Line 50:
 ==== Interconnections ==== ==== Interconnections ====
  
-{{::​scsoled:​j1.png?​nolink&​400|}} +  * J1 is a power header ​with +5V as markedmiddle pin 0V. 
- +  * J2 normally connects ​to Core J4B (I2C) 
-J1 is the SCS header, ​connecting ​to J10A +  * J3 carries the WS2812B chain for additional modules 
- +  * J4-7 connect to DINX4 headers
-J2 can provide power as indicated; it is also connected on J5.+
  
-J5 connects to J15 on the Core (or equivalent) 
  
 ===== Dimensions ===== ===== Dimensions =====
enc_4_4.1520361744.txt.gz · Last modified: 2018/03/06 18:42 by latigid_on